A. Low temperature of
B. High temperature of
C. High % of CO in
D. High % of CO2 in
Correct Answer: High % of CO in ✔
Last Updated: February 11, 2019
Related MCQs
- Which of the following terminology is used for the temperature at which new grains are formed in a metal ?
- In __________ process, there is an increase in entropy with no degradation of energy ?
- Air-petrol ratio in an automotive petrol engine is around __________?
- __________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength ?
- Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2) ?
- Pick out the wrong conversion of absolute & kinematic viscosities ?
- The stress at which extension of the material takes place more rapidly as compared to the increase in load is termed as the __________ point of the material?
- An approximately __________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section ?
- Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%?
- Nickel is a __________ material?
- The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the__________?
- Function of fusible plug in a boiler is to __________?
- High endurance limit of carburised machine parts is because of the fact that carburisation __________?
- Optical activity is a/an __________ property ?
- “Encyclopaedia of Chemical Technology” has been __________?
- Otto cycle used in spark ignition petrol engines is also known as the constant __________ cycle?
- A material being tested for endurance strength is subjected to the __________ load?
- __________ is not used as a material of construction in thermocouples ?
- A metal having a Poisson’s ratio = 0.3 is elastically deformed under uniaxial tension. If the longitudinal strain = 0.8, then the magnitude of thickness strain is__________?
- For dynamic strain measurement, the Wheatstone bridge used is of __________ type ?
- The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called__________?
- More than 95% of __________ is present in corundum ?
- L.D. (Linz-Donawitz) converter is used in the production of__________?
- Which of the following contributes maximum as main source of sulphur in the blast furnace charge ?
- Constituents of stellite are __________?
- Which of the following pairs is not correctly matched ?
- When dry bulb temperature & wet bulb temperature of moist air is the same, it means that the __________?
- Specific gravity of hot metal (pig iron) is __________ times that of the blast furnace slag ?
- What happens, when SO2 is passed through a solution of H2S in water ?
- Pick out the wrong statement?
- Identify the false statement?
- Steels with high carbon equivalent have poor Weldability, because in these steels during welding__________?
- Blasting of tri-nitro-toluene (TNT) is done by mixing it with ammonium__________?
- Joule-Thomson co-efficient is the ratio of__________?
- Which of the following material handling equipments is not suitable for moving materials in varying paths ?
- Pick out the wrong statement ?
- __________ property of a material is determined by the Herbert Pendulum device?
- The activity co-efficient of the solute in a dilute solution ?
- Insulation of liquid surface can be achieved by __________ on top of its surface?
- At absolute zero temperature, for any reaction involving condensed phases ?
- If a solid is compressed adiabatically in its elastic range, its __________ remains constant ?
- Natural water contains approximately __________ percent of heavy water?
- Exposure to __________ accelerates the degradation of plastics?
- The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) ?
- Production of one ton of paper in Indian paper industry consumes about __________ kWh of electricity ?
- A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre?
- For grinding of softer materials, the grinding wheel should have __________ grain size ?
- Consider an ideal solution of components A and B. The entropy of mixing per mole of an alloy containing 50% B is__________?
- In case of compression of one kg of air, the work done will be the least, when the value of polytropic index ‘n’ is__________?
- The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) ?
- Corrosion rate cannot be lowered by reducing the __________ of the corroding medium?