A. Less than the wet bulb temperature
B. More than the wet bulb temperature
C. Equal to the wet bulb temperature
D. Equal to the ambient temperature
Correct Answer: More than the wet bulb temperature ✔
Last Updated: February 08, 2019
Related MCQs
- In a neutral solution__________?
- Elimination of brittleness resulting from welding of saw blades is done by __________ of the welded portion ?
- Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA) ?
- Maximum permissible air velocity in pipelines is about __________ metre/second ?
- Resilience of a bolt can be increased by increasing its __________?
- __________ temperature remains constant during adiabatic saturation process of unsaturated air ?
- The refractory brick which has good thermal shock resistance at high temperature but cracks on cooling below 400°C is__________?
- Use of economiser in a boiler plant reduces the fuel consumption for steam generation by about __________ percent ?
- Work done by a/an __________ process is determined by ∫p. dv ?
- In troposphere (the weather domain), the temperature ‘t’ at height ‘h’ above the sea level in metres is given by (where, temperature at sea level is 15°C and t is in °C.) ?
- Induced draft fans provided in large thermal power plant boilers have __________ blades?
- Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories ?
- Wood is a/an __________ material ?
- In condensers used in thermal power plants, steam is normally used in shell side and cooling water on the tube side, because of the reason that ?
- Steel balls are manufactured by__________?
- __________ are normally subjected to sub-zero treatment?
- Auto collimator is used to check__________?
- __________ fluid force is not considered in the Navier-Stokes equation?
- The most important consideration in value engineering is the__________?
- Which of the following is not an explosive ?
- ‘Ice point’ is designated on Fahrenheit temperature scale by__________?
- Maximum consumption of limestone is in the __________ industry?
- Dies for wire drawing are generally made of__________?
- Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore ?
- Copper deposits are found in India at the following location ?
- Out of the following, the joint produced by __________ has the lowest strength?
- Aluminium is extracted from__________?
- If a nuclear reactor produces more fissile nuclear fuel than it consumes, then it is called a __________ reactor?
- Metalloids__________?
- Use of flux during soldering is done to__________?
- __________ is the most suitable lubricant for drawing mild steel wires?
- Fog is an example of colloidal system of__________?
- A jet engine turbine blade is normally manufactured by__________?
- Square steel key is normally strong in failure by shear & crushing. Keys are normally made of __________ steel bars?
- Wrought iron does not have__________?
- X-rays are__________?
- In extrusion of metals, which of the following statement is true ?
- A solar cell converts the sunlight directly into __________ energy?
- The friction factor for the turbulent fluid flow in a rough pipe does not depend upon the__________?
- Which of the following does not discharge the dust collected as a dry solid?
- Hydro-cyclone is a__________?
- Tin based white metals are used, where bearings are subjected to__________?
- The cooling rate required to freeze 1 ton of water at 0°C into ice at 0°C in 24 hours is __________ BTU/hr?
- For preparation of porous bearings by powder metallurgy, preferred particle shape is__________?
- __________ is the hardest oxide and is hence used where high wear resistance at high temperature is required?
- Cobalt – 60 is used as a source of __________ in medical therapy & industrial radiography?
- __________ is used for tying the steel columns to concrete foundation?
- Alloys having more than 80% copper are generally more__________?
- Friction factor for fluid flow in pipe does not depend upon the__________?
- Which of the following is preferred for riveting ?
- In case of simple harmonic motion, displacement is proportional to the__________?