A. Shear stress is maximum
B. Velocity gradient is flat
C. Density variation is maximum
D. Shear stress is zero
Correct Answer: Shear stress is maximum ✔
Last Updated: February 08, 2019
Related MCQs
- Uniform ramming of sand in green sand moulding process leads to__________?
- __________ flux is used for the extraction of metal from its self fluxing ores?
- Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about__________?
- During decarburising of a plain carbon steel, the thickness of ferrite layer growth is proportional to__________?
- Property responsible for the talcum powder to cling to the skin is the__________?
- Breakeven point represents the condition, when the company runs under no profit no loss condition. In break even analysis, total cost comprises of fixed cost__________?
- Principal alloying elements of cast tool alloys which have very high wear resistance & high temperature strength are ?
- Which of the, following is not associated with the functioning of a petrol engine ?
- Heating of ferromagnetic materials to a temperature above Curie temperature makes it __________?
- Oxygen cylinders used for autogenous (cutting/welding) purposes are __________?
- Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is__________?
- The pressure outside a bubble/droplet of liquid is __________ the internal pressure?
- __________ joint is usually used for joining cast iron pipes mostly used for temporary pipelines, where it may be necessary to dismantle & reassemble the pipeline very frequently ?
- Which of the following varies as the square root of oil pressure during atomisation of fuel oil through a pressure jet burner ?
- The value of y = cp/cv. at < 500°C for air & most common gases can be safely assumed to be__________?
- __________ of air does not increase with increase in temperature?
- ‘Cryogenics’ is concerned with the generation & use of low temperature in the range of__________?
- The heat of neutralisation remains constant, when there is a reaction between dilute solutions of strong __________?
- Carbon is present in the form of __________ in grey cast iron ?
- Spherical shape of mercury droplets is due to its__________?
- Increase in the entropy of a system represents the__________?
- Minimum number of members required to form a Public Limited Joint Stock Com-pany is__________?
- Damage to metal surface by mechanical action is called__________?
- Stresses encountered in the metal forming processes are less than the __________ of the material?
- Materials having __________ lattice structure are usually the most ductile ?
- Presence of nickel & chromium in steel does not raise its __________?
- Current employed in resistance welding ranges from __________ kVA/cm2?
- Which of the following has the least value of ultimate tensile strength (UTS) ?
- With increase in compression ratio, the volumetric efficiency of air compressor__________?
- Compressed dry air is used as the cutting fluid, while machining__________?
- With increase in temperature, the surface tension of water__________?
- Brittleness induced due to the presence of sulphur in steel can be reduced by adding__________?
- In practice, the compression ratio of compression-ignition (CI) engine ranges from __________?
- The specific gravity of coal depends mainly on its __________ content ?
- The refractory lining of the bottom in a basic electric arc furnace is made of__________?
- Unit of viscosity in CGS system is__________?
- A dummy activity is used in PERT network to describe the__________?
- Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint ?
- Carnot cycle is also termed as the constant __________ cycle in thermodynamics?
- Matte smelting is used in the extraction of__________?
- The ratio of mass of a neutron to that of an electron is about 1839. What is the ratio of the mass of a proton to that of an electron ?
- Good design of the casing of a centrifugal pump aims at minimising the __________?
- Austempering process results in the formation of __________ structure ?
- Minimum safe distance between two liquid fuel storage tanks is equal to (where, H = height of the tank) ?
- Which of the following is prone to cup and cone fracture ?
- Particle nature of cathode rays is proved due to the fact that they __________?
- Which of the following is not a dielectric material ?
- The most suitable material of construction for a sewer to carry sewage under high pressure is__________?
- In “Imperial Smelting Process” for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following __________?
- The rolling process cannot be used to produce__________?
- Boiler tube size is specified by its thickness and __________ diameter ?