A. -55°
B. -40°
C. -33°
D. -58°
Correct Answer: -40° ✔
Last Updated: February 08, 2019
Related MCQs
- Increasing sulphur content in pig iron tends to make it __________?
- The substance used as a smoke screen in warfare is__________?
- The mechanism which changes the value of manipulated variable in response to the output signal from the control unit is called the__________?
- Carbide tipped cutting tools are manufactured by powder metallurgy techniques and have a composition of__________?
- Which of the following low melting alloy containing bismuth and lead is used for electric fuse ?
- Specific gravity of a metal, which weighs 5 kg in air and 4 kg when submerged in water, will be__________?
- Midrex process of sponge iron production uses reformed natural gas as the reducing agent, which uses iron ore in the form of__________?
- Brazing is the joining of metals__________?
- Cementite is in the lamellar form in the __________ phase of steel ?
- Difference at any instant between the value of the controlled variable and the set point is called the__________?
- The boiling & freezing points on a newly defined temperature scale in degree ‘D’ are 400°D & 100°D respectively. The temperature reading corresponding to 60°C on this new temperature scale will be equal to __________ °D ?
- Limestone is added in the blast furnace (during pig iron manufacture) to__________?
- Which of the following equipments is used for liquid dispersion ?
- Which of the following metals cannot be hot worked at room temperature ?
- Which of the following phenomenon will exhibit the minimum heat transfer ?
- Corrosion is__________?
- Super heating of steam is done at constant__________?
- Silicon in steel__________?
- Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature ?
- Which of the following is an unconventional source of energy ?
- Wave length of X-rays is about 1 angstrom; however it cannot pass through a sheet of __________?
- For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by__________?
- The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag ?
- The same volume of all gases is representative of their__________?
- ‘Amortization’ in respect of financial obligation of a company means the__________?
- The surface tension of a liquid, at critical temperature is__________?
- The lightest non-inflammable gas is__________?
- Nickel and __________ are the alloying element added in steel to increase its toughness?
- Hydrogen in liquid steels is dissolved__________?
- Thermal efficiency of an internal combustion engine is around __________ percent?
- Which of the following is the most wear resistant grade of carbide used for the cutting tools ?
- Laser is a device to produce__________?
- Basic open hearth furnace (BOF) is not used for producing __________ steel?
- __________ circuit is most commonly used to measure strain with the help of a strain gauge?
- Lead is poured into the joint between two __________ pipes ?
- Co-efficient of performance of a Carnot cycle refrigerator operating between – 23°C and + 27°C is __________?
- Unit of surface tension in S.I. unit is__________?
- The noble metals__________?
- Which of the following is the most suitable abrasive for grinding high tensile strength materials ?
- The majority charge carriers in p-type silicon are__________?
- Quartz is a __________ material ?
- Force between the molecules of the same substance is called __________ force?
- Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of__________?
- Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per m2 of steel strip ?
- The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength ?
- __________ is a special constituent of chlorophyll without which photosynthesis is not possible ?
- Steel is welded using the __________ flame ?
- Which of the following metals reacts violently with water ?
- The minimum and the maximum number of members required to form a Private Limited Joint Stock Company are respectively __________?
- Bad odour in sanitary latrines is reduced by periodically sprinkling__________?
- __________ test determines the yield strength, Young’s modulus of elasticity, percentage reduction in area & percentage elongation of a material ?