A. Brake linings
B. Bearings
C. Carbide tool tips
D. All A, B and C
Correct Answer: All A, B and C ✔
Last Updated: February 11, 2019
Related MCQs
- Pick out the wrong statement about nucleate boiling ?
- Latent heat of dry steam at atmospheric pressure is 539 Kcal/kg; which __________ with increase in the pressure of steam?
- With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected ?
- The bank of tubes located at the back of the domestic refrigerators are the __________ tubes?
- Mho’s scale of hardness, which consists of 10 standard minerals is used for the measurement of __________ hardness?
- Electrometallurgy is not involved in the extraction of __________ from its ore?
- Screws are specified by their __________ diameters?
- Cupola produces __________ iron?
- A semi-conductor is damaged & behaves like a conductor, on passing a strong electric current through it, because it heats up the crystals & breaks the covalent bonds resulting in __________ electrons ?
- In a furnace with heating element temperature at 1700°C, the dominant mechanism of heat transfer will be__________?
- Pick out the wrong statement about coating/electroplating of metals ?
- Nusselt number/Biot number varies__________?
- Hooke’s law__________?
- In case of a, centrifugal pump, the ratio h1/h2 is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller)?
- Increase in temperature, in general results in the__________?
- Which of the following fastening devices has its both ends threaded ?
- Dryness fraction of dry steam is__________?
- Specific __________ is a dimensionless quantity ?
- ‘GASOHOL’ widely used in Brazil as a motor fuel is a mixture of alcohol and__________?
- Batch process is preferred over continuous process, when the__________?
- Which of the following processes follows the hardening process for reducing the hardening strains & increasing the toughness of the steel part ?
- Electrochemical corrosion can occur, only if __________ is present in contact with metal?
- The ability of tool steel to resist softening at high temperatures is termed as __________ hardness?
- In the acid Bessemer process, the hot metal should have the following composition ?
- A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to__________?
- Work study deals with the __________ study?
- Gross national product (GNP) means the total value of __________ in a country ?
- Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position ?
- The efficiency of a Carnot heat engine operating between absolute temperatures T1 and T2 (when, T1 > T2) is given by (T1 – T2)/T1. The co-efficient of performance (CO.P.) of a Carnot heat pump operating between T1 and T2 is given by__________?
- Blow off cock is provided in steam boiler to __________?
- The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the__________?
- __________ pipe is the most suitable for carrying sanitary drainage?
- Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode__________?
- Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to__________?
- Holes for riveting purposes should be preferably made by__________?
- Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30% ?
- Triple point of water is__________?
- Ganister contains maximum percentage of__________?
- Energy to be supplied to the radioactive nucleus for the emission of a neutron is __________ MeV?
- Euler number is defined as the ratio of inertia force to __________ force?
- The co-ordination number in simple cubic structure is__________?
- In inventory control theory, the economic order quantity (EOQ) is the__________?
- In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will __________?
- Liquor poisoning generally occurs due to the presence of __________ in it?
- Heat required to raise the temperature of a body by 1 °C is called its__________?
- Solute atoms which cause yield point phenomenon in mild steel are/is__________?
- ‘Flare tower’ used in industry is meant for__________?
- The ratio of thermal & electrical conductivity is same for all the metals at the same temperature; and at around room temperature, this ratio is proportional to(where, T = absolute temperature, °K) ?
- Common salt is produced from sea water in India generally by the __________ method?
- Which of the following phenomenon/ phenomena is/are diffusion controlled ?
- Air/fuel ratio on molar (volume) basis for combustion of methane with theoretical quantity of air with be__________?