Home
About Us
Contact Us
Privacy Policy
Search
Home
→
Chemical Engineering Basics
→
Which of the following metals cannot be hot worked at room temperature ?
Related MCQs
Which of the following phenomenon will exhibit the minimum heat transfer ?
Corrosion is__________?
Super heating of steam is done at constant__________?
Silicon in steel__________?
Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature ?
Which of the following is an unconventional source of energy ?
Wave length of X-rays is about 1 angstrom; however it cannot pass through a sheet of __________?
For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by__________?
The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag ?
The same volume of all gases is representative of their__________?
‘Amortization’ in respect of financial obligation of a company means the__________?
The surface tension of a liquid, at critical temperature is__________?
The lightest non-inflammable gas is__________?
Nickel and __________ are the alloying element added in steel to increase its toughness?
Hydrogen in liquid steels is dissolved__________?
Thermal efficiency of an internal combustion engine is around __________ percent?
Which of the following is the most wear resistant grade of carbide used for the cutting tools ?
Laser is a device to produce__________?
Basic open hearth furnace (BOF) is not used for producing __________ steel?
__________ circuit is most commonly used to measure strain with the help of a strain gauge?
Lead is poured into the joint between two __________ pipes ?
Co-efficient of performance of a Carnot cycle refrigerator operating between – 23°C and + 27°C is __________?
Unit of surface tension in S.I. unit is__________?
The noble metals__________?
Which of the following is the most suitable abrasive for grinding high tensile strength materials ?
The majority charge carriers in p-type silicon are__________?
Quartz is a __________ material ?
Force between the molecules of the same substance is called __________ force?
Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of__________?
Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per m2 of steel strip ?
The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength ?
__________ is a special constituent of chlorophyll without which photosynthesis is not possible ?
Steel is welded using the __________ flame ?
Which of the following metals reacts violently with water ?
The minimum and the maximum number of members required to form a Private Limited Joint Stock Company are respectively __________?
Bad odour in sanitary latrines is reduced by periodically sprinkling__________?
__________ test determines the yield strength, Young’s modulus of elasticity, percentage reduction in area & percentage elongation of a material ?
Material of construction of foundry crucible is __________?
The thermodynamic law, PVy = constant, is not followed by the __________?
To counteract the bad effects of strain hardening on a cold formed part, it must be __________?
Liquid nitrogen containers can be made from __________?
When the wavelength of incident X-rays increases, the angle of diffraction__________?
__________ property of steel increases by addition of large amount of silicon in it?
In case of condensers & evaporators operating under given terminal conditions, LMTD (logarithmic mean temperature difference) for counter flow as compared to that for parallel flow is__________?
At the point of boundary layer separation in fluid flow, the __________?
Uniform ramming of sand in green sand moulding process leads to__________?
__________ flux is used for the extraction of metal from its self fluxing ores?
Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about__________?
During decarburising of a plain carbon steel, the thickness of ferrite layer growth is proportional to__________?
Property responsible for the talcum powder to cling to the skin is the__________?
Breakeven point represents the condition, when the company runs under no profit no loss condition. In break even analysis, total cost comprises of fixed cost__________?
Which of the following metals cannot be hot worked at room temperature ?
A. Zinc
B. Nickel
C. Lead
D. Tin
Correct Answer:
Nickel
✔
Last Updated:
February 08, 2019