Home
About Us
Contact Us
Privacy Policy
Search
Home
→
Fluid Mechanics for Chemical
→
Hydraulic diameter for non-circular ducts is equal to ___________ times the area of flow divided by the perimeter?
Related MCQs
Froude number is the ratio of__________?
A stream line is__________?
Which of the following is used for pumping crude oil from oil well ?
The buoyant force acting on a floating body is dependent on the __________?
Horsepower requirement for given pump capacity depends upon the__________?
For a given Reynolds number, in a hydraulically smooth pipe, further smoothening __________ the friction factor?
Disc compensators are provided in large diameter fuel gas carrying pipelines to__________?
The unit of velocity head is__________?
The capacity of a centrifugal pump Can be increased by increasing the__________?
Curve III in the bellow diagram represents a/an__________?
The main factor on which the behaviour of a mass of fluidised solid depends mainly is the__________?
Umf is the minimum fluidisation velocity for a bed of particles. An increase in the superficial gas velocity from 2 Umf to 2.5 Umf results in (all velocities are smaller than the entrainment velocity of the particles) no change in the__________?
What is the unit of kinematic viscosity in SI unit ?
A rectangular surface 3′ × 4′, has the lower 3 edge horizontal and 6′ below a free oil surface (sp. gr. 0.8). The surface inclination is 300 with the horizontal. The force on one side of the surface is (where, y = specific weight of water) ?
A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun’s equation for the above fluid-particle system (in SI units) is given below: Δ P/L = 375 × 103 VOM + 10.94 × 106 V2 OM (SI units) If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed ?
In power law, δ = [A (du/dy)2 + B] then the fluid is__________?
Drag co-efficient for motion of spherical particles in a stationary fluid in the stoke’s law range is__________?
Terminal velocity is__________?
In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller?
In area meter (e.g., Rotameter), with increase in the fluid flow rate, the__________?
Minimum porosity for fluidisation is__________?
Isothermal turbulent flow of a fluid results in decrease of its pressure, which depends on the__________?
Momentum correction factor used in fluid flow problems accounts for the__________?
A compressor that takes suction at a pressure below atmospheric and discharge against atmospheric pressure is called a __________ pump?
A mixed flow centrifugal pump__________?
Which of the following has the maximum compression ratio ?
For a stable equilibrium of a submerged body (where, G and B are centres of gravity & buoyancy respectively) ?
Volute of a centrifugal pump should be designed in a fashion, such that the__________?
In a stabilised soap bubble, pressure inside it compared to external pressure is__________?
The contraction co-efficient for Borda’s mouthpiece (for frictionless fluid) is__________?
The value of critical Reynolds number for pipe flow is__________?
The range of a particular Rotameter can be increased by__________?
Propellers are__________?
Cavitation occurs in a centrifugal pump when the suction pressure is__________?
Erosion and pits formation on the impeller of a centrifugal pump may be due to__________?
What is the ratio of total kinetic energy of fluid passing per second to the value obtained on the basis of average velocity (for laminar flow through a circular pipe) ?
The curve of metacentre for a floating body __________ the curve of buoyancy?
Slugging occurs in a fluidised bed, if the bed is__________?
Unsteady non-uniform flow is represented by flow through a/an__________?
In case of turbulent flow of a Newtonian fluid in a straight pipe, the maximum velocity is equal to (where, Vavg = average fluid velocity)?
Which law is followed by the velocity distribution in the turbulent boundary layer ?
f = 16/NRe, is valid for__________?
Which of the following exemplifies a three dimensional fluid flow ?
Piezometric head is the sum of the __________ heads?
The discharge through a semi-circular weir varies as (where, H = Head of liquid.) ?
Hydraulic __________ works on the principle of Pascal’s law of transmission of fluid pressure?
Multistage compressors are used in industry, because they__________?
Dimension of kinematic viscosity is__________?
In case of Couette flow, the fluid flow is between two large flat parallel plates with__________?
Weber number is the ratio of inertial force to __________ force?
Potential flow is the flow of__________?
Hydraulic diameter for non-circular ducts is equal to ___________ times the area of flow divided by the perimeter?
A. Two
B. Three
C. Four
D. Eight
Correct Answer:
Four
✔
Last Updated:
March 10, 2019