A. Fluid to that of the light
B. Light to that of the fluid
C. Fluid to that of the sound
D. Sound to that of the fluid
Correct Answer: Fluid to that of the sound ✔
Last Updated: March 09, 2019
Related MCQs
- Actual lift of a pump is always less than the theoretical lift and is limited by the__________?
- Low specific speed of a pump implies that, it is a/an __________ pump?
- Function of air vessel provided in a reciprocating pump is to__________?
- A relief valve__________?
- Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) __________?
- Drag is defined as the force exerted by the__________?
- One poise (unit of absolute/dynamic viscosity) is equivalent to one__________?
- With increase in molecular weight of the gas, the head developed by a centrifugal compressor will__________?
- In case of a pipe exit fitted with a nozzle, the__________?
- Which of the following can be used to create a flow of gas, where no significant compression is required ?
- The ratio of inertial forces to viscous forces is called the __________ number?
- In laminar flow through a round tube, the discharge varies __________?
- Fanning friction factor for laminar flow of fluid in a circular pipe is__________?
- A hydraulic accumulator comprises of__________?
- A pump operating under specific conditions delivers insufficient quantity of liquid. This may be set right by__________?
- The ratio of pressure forces to inertial forces is called the __________ number?
- In case of turbulent flow of fluid through a circular pipe, the __________?
- The ratio of the depth of flow to the diameter of the channel for maximum discharge in a circular channel in open channel flow is__________?
- Forces acting on a particle settling in fluid are __________ forces?
- Fluid resistance to shear depends upon its__________?
- Which of the following relationship is valid for the equilibrium position of the float in a Rotameter? (Where, Df= Drag force on the float Bf = Buoyant force on the float Wf = Weight of the float)?
- The equation relating friction factor to Reynold number, f-0.5 = 4 loge (NRe/√f)-0.4, is called the __________ equation?
- Applicability of Bernoulli’s equation is limited to a/an __________ fluid, that does not exchange shaft work with the surroundings?
- Potential flow is characterised by the__________?
- Viscosity of water at 40°C lies in the range of__________?
- Prandtl mixing length is__________?
- The pressure co-efficient is the ratio of pressure forces to __________ forces?
- In magnetic flow meters, voltage generation is__________?
- Which of the following is a Newtonian fluid ?
- In which of the following body shapes, the pressure drag is large compared to the friction drag ?
- Pressure drop in a fluidised bed reactor is __________ that in a similar packed bed reactor?
- When the water is warm, the height to which it can be lifted by a pump__________?
- In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes__________?
- Which of the following is the most common pump for pumping either raw sewage or sludge ?
- In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow ?
- The boundary layer is that part of a moving fluid, in which the fluid velocity is__________?
- For turbulent flow of an incompressible fluid through a pipe, the flow rate „Q‟ is proportional to (Δ P)n, where ΔP is the pressure drop. The value of exponent ‘n’ is__________?
- What is the value of Fanning friction factor f ‘ for smooth pipe at NRe = 106 approximately ?
- In the complete turbulence zone (in rough pipes), the__________?
- Reynolds number for flow of water at room temperature through 2 cm dia pipe at an average velocity of 5 cm/sec is around__________?
- Equivalent length of a pipe fitting is__________?
- In deriving Bernoulli’s equation, fluid is assumed to be__________?
- Self-priming centrifugal pump can be used for__________?
- Discharge in laminar flow through a pipe varies__________?
- A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute ?
- Which of the following is most prone to pulsating discharge flow ?
- I.D. of 1/4″ schedule 40 pipe is 0.364″. I.D. of a 1/2″ schedule 40 pipe would be __________ inch?
- Slurries can be most conveniently pumped by a __________ pump?
- Poise is converted into stoke by __________?
- A tube is specified by its__________?
- In parallel pipe problems, the__________?