A. Reciprocating
B. Gear
C. Centrifugal
D. Diaphragm
Correct Answer: Centrifugal ✔
Last Updated: March 10, 2019
Related MCQs
- The head developed by a centrifugal pump is largely determined by the__________?
- Applying a pressure drop across a capillary results in a volumetric flow rate ‘Q’ under laminar flow conditions. The flow rate for the same pressure drop, in a capillary of the same length but half the radius is__________?
- A stream tube is that, which has __________ cross-section entirely bounded by stream lines?
- A fluid element has a velocity V = -y2. xi + 2yx2 . j. The motion at (x, y) = (1/√2, 1) is__________?
- Centrifugal compressors compared to reciprocating compressors__________?
- The ratio of inertial forces to elastic forces is called the __________ number?
- The fluid property, due to which, mercury does not wet the glass is__________?
- The head loss in turbulent flow in a pipe varies__________?
- Co-efficient of discharge (Cd) is defined as actual discharge/theoretical discharge and is equal to Cc . Cv; where Cc = Co-efficient of contraction and Cv = co-efficient of velocity. Cd of an orifice is usually about__________?
- The excess of the sum of pressure & velocity heads over the vapor pressure of the liquid at the suction is called the__________?
- Rise of liquid in a capillary tube is due to__________?
- The pressure head on sudden contraction in a horizontal pipe is converted into the __________ head?
- For very low pressure and high discharge rate, the compressor used is a/an __________ compressor?
- A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun’s equation for the above fluid-particle system (in SI units) is given below : Δ P/L = 375 × 103 VOM + 10.94 × 106 V2 OM (SI units) If water is to be used as the fluidising medium, the minimum fluidisation velocity, VOM is__________?
- Non-colloidal solution is an example of the __________ fluid?
- One dimensional flow implies__________?
- Out of the following flow measuring devices, which one incurs the maximum installation cost as well as pressure loss ?
- __________ forces do not act in case of fluid flow ?
- With increase in the ratio of orifice diameter to pipe diameter in case of an orificemeter, the overall pressure loss__________?
- Fanning friction factor is equal to (where, fB = Blasius friction factor) ?
- What is the speed of sound (m/sec) in ordinary water ?
- Which of the following is not an advantage of fluidisation from transfer operation point of view ?
- While starting an axial flow pump, its delivery valve should be kept __________?
- The line traced by a single fluid particle as it moves over a period of time is called __________ line?
- Pumping of a corrosive liquid is generally preferred to be done by a __________ pump, as it can be made of a variety of materials including plastics?
- For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) ?
- For the same flow rate of a fluid, the pressure drop is the least for __________?
- Discharge from a 24 inch pipe of water at 10 ft/sec will be __________ ft3/sec?
- Rubber latex is an example of __________ fluid?
- Diaphragm pumps are used to transport__________?
- The length of the tube necessary for the boundary layer to reach the centre of the tube and for fully developed flow to be established is called the __________ length?
- With decrease in particle size to be fluidised by a particular fluid, the operating range of fluidisation velocity__________?
- Differential manometer measures the__________?
- __________ pumps are a group of vacuum pumps ?
- The momentum correction factor for the velocity distribution of laminar flow is__________?
- The frictional resistance in laminar flow does not depend on the__________?
- Steady non-uniform flow is exemplified by flow through a/an__________?
- For an incompressible fluid, the bulk modulus of elasticity is__________?
- Pressure drop in a packed bed for laminar flow is given by the __________ equation?
- The line of action of the buoyant force acts through the__________?
- Bernoulli’s equation accounts for the__________?
- A Newtonian fluid is that__________?
- A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp?
- Power number is the ratio of__________?
- A hydraulic press has a ram of 10 cms in diameter and a plunger of 1 cm in diameter. The force required on the plunger to raise a weight of 10 tons on the ram is __________ kg?
- Mach number is defined as the ratio of the local flow velocity to the sonic velocity in the fluid. For what value of Mach number, the gases are considered incompressible ?
- Propeller type centrifugal pumps are most suitable for__________?
- Hydraulic diameter for non-circular ducts is equal to __________ times the area of flow divided by the perimeter?
- Froude number is the ratio of__________?
- A stream line is__________?
- Which of the following is used for pumping crude oil from oil well ?