A. Pressure
B. Height of descend
C. Viscosity
D. Surface tension
Correct Answer: Surface tension ✔
Last Updated: March 10, 2019
Related MCQs
- Priming of a centrifugal pump is done to__________?
- Pick out the wrong statement pertaining to fluid flow ?
- The ratio of the wall drag to the form drag in the Stoke’s law range (for motion of spherical particles in a stationary fluid) is__________?
- The discharge through a Venturimeter depends upon __________?
- The head loss due to sudden expansion is__________?
- Which of the following two quantities when same, makes one pipe system equivalent to another pipe system ?
- Choose the correct set of dimensions of viscosity that are equivalent (where, F, M, L, T are dimensions for force, mass, length and time respectively) ?
- Small pressure differences in liquids is measured using a/an__________?
- Two dimensional stream function__________?
- The pressure drop per unit length of pipe incurred by a fluid ‘X’ flowing through pipe is Δp. If another fluid ‘Y’ having both the specific gravity & density just double of that of fluid ‘X’, flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be__________?
- Euler’s equation of motion is a statement expressing__________?
- Steady flow occurs, when the__________?
- Euler’s equation of motion states, that at every point, the__________?
- For the free settling of a spherical particle through a fluid, the slope of, CD-log NRe, plot is__________?
- For a specific centrifugal air blower operating at constant speed & capacity, the power requirement and pressure vary__________?
- The discharge co-efficient for an orifice meter does not depend upon the __________?
- Velocity at a certain point in case of streamline flow is__________?
- The speed of sound in an ideal gas varies as the __________?
- Unsteady uniform flow is represented by flow through a/an__________?
- For flow of fluids through packed bed, the superficial velocity is__________?
- Various efficiencies of a centrifugal pump are related as (where, εm = mechanical efficiency εv = volumetric efficiency. εma = manometric efficiency εo = overall efficiency) ?
- For ideally incompressible fluid, the Mach number will be __________?
- The specific speed of a pump is defined as the speed of a unit of such a size, that it__________?
- What is the normal range of exit cone angle of a Venturimeter ?
- Centrifugal pump is normally classified on the basis of the__________?
- The phenomenon occuring during pumping of a liquid solution containing dissolved gases, which may come out of the solution giving rise to gas pockets, is termed as__________?
- Centre of pressure in an immersed body is __________ the centre of gravity?
- Re/NFr is called the __________ number?
- Drag force acting on a body does not depend upon the__________?
- The dimension of kinematic viscosity is__________?
- Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller?
- Pascal’s law is valid, only when the fluid is__________?
- Fluid flow at increasing rate through a diverging pipe is an example of __________ flow?
- Which of the following assumptions enables the Euler’s equation of motion to be integrated ?
- What is the pipe called which lifts water from a reservoir to a greater height than the initial level in the supply reservoir ?
- In turbulent flow, a rough pipe has the same friction factor as a smooth pipe__________?
- A fluid is pumped at the rate of 10 lb/sec to a height of 55 ft. The horse power required is __________ hp?
- A pitched-blade turbine draws __________ a straight blade turbine?
- Absolute viscosity of a fluid is a function of the __________ of the fluid?
- For one dimensional flow of an incompressible fluid in unsteady state in x-direction, the continuity equation is given by__________?
- What is the normal range of exit cone angle of a Venturimeter ?
- The __________ is measured by a piezometric opening?
- Which of the following is not concerned with the fluid-particle interaction ?
- Fluidised beds are formed, when the__________?
- The terminal velocity of a particle moving through a fluid varies as dp n. What is the value of n’ for Newton’s law regime ?
- The inherent characteristic of an equal percentage valve relating flow rate ‘q’ with valve stem movement ‘x’ are described by the equation__________?
- Co-efficient of velocity is __________ the coefficient of discharge?
- A Rotameter through which air at room temperature and atmospheric pressure is flowing gives a certain reading for a flow rate of 100 cc/sec. If helium (molecular weight 4) is used and Rotameter shows the same reading, the flow rate (cc/sec) is__________?
- The terminal velocity of a small sphere settling in a viscous fluid varies as the__________?
- For pipes that must be broken at intervals for maintenance, the connector used should be a/an__________?
- A mono pump is a __________ pump ?