A. Reduces the flue gas temperature and makes the furnace atmosphere oxidising
B. Increases the load on the induced draft fan
C. Reduces the furnace draught
D. All A., B. and C.
Correct Answer: D. All A., B. and C. ✔
Last Updated: March 11, 2019
Related MCQs
- Fuel economy in furnaces can be achieved by__________?
- __________ is an indirectly heated furnace?
- Furnace pressure is normally controlled by regulating the__________?
- Which one is not an induced draught furnace ?
- Ceramic coating material for furnace refractory, which increases its emissivity and thus the radiation heat transfer rate in the furnace, comprises of__________?
- Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an__________?
- Reducing atmosphere is maintained in a__________?
- The amount of combustible escaping unconsumed from the furnace, depends upon the__________?
- Heat transfer rate to the charge/stock in a furnace does not depend upon the__________?
- Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by__________?
- Overall thermal efficiency of a lumpy coal fired suitably designed heating furnace, if operated & maintained properly may be about __________ percent?
- An example of recuperative furnace is the__________?
- In a furnace employing forced draught as compared to induced draught__________?
- Which is a regenerative furnace ?
- In order to maintain an oxidising atmosphere in a furnace, it should have__________?
- Heat transfer rate to the stock/charge in the furnace does not depend upon the__________?
- The main function of a muffle in the muffle furnace is to__________?
- In a furnace operation, which is not preheated ?
- Fuel used in B.F. stove is__________?
- Reverberatory furnace is used for__________?
- Which furnace employs an I.D. fan for the removal of flue gases from the furnace ?
- Cement Kiln is a__________?
- Which of the following accentuates clinkering troubles on furnace grate burning coal ?
- Oxygen percentage in the flue gas coming out of a gaseous fuel fired furnace should be ideally about __________ percent?
- Means for giving direction to the circulation of gases in furnaces are__________?
- Heat balance of furnace provides means of determining the__________?
- If fuel and air are mixed ahead of the burner, it is called a/an __________ burner?
- Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by__________?
- Which of the following is a directly fired intermittent furnace ?
- In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of__________?
- Example of an indirectly heated furnace is__________?
- Use of pulverised coal in boilers provides__________?
- Waste heat from the outgoing flue gases in a thermal power plant is recovered by a/an__________?
- Which of the following is not a continuous waste heat recovery equipment from the flue gases going out of furnace ?
- Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace ?
- An example of a periodic furnace is the__________?
- Which of the following variables does not affect the furnace capacity ?
- Circulation of gases in furnace is caused by the__________?
- Which is not accomplished in an underfired furnace ?
- The purpose of controlling the furnace atmosphere is to prevent surface attack by__________?
- Regenerators as compared to recuperators for the same duty__________?
- Dampers are located__________?
- The resistance furnace produces heat by the__________?
- Thickness of stock does not affect the fuel economy of furnaces, if the material to be heated is of__________?
- An example of indirectly heated furnace is the__________?
- Neutral atmosphere is maintained in a/an __________ furnace?
- The thermal efficiency of a steel slab reheating furnace (walking beam type) may be about __________ percent?
- In low or standard frequency induction furnace, heat is produced by the__________?
- The rate of scaling of furnace stock depends upon the__________?
- The reason for excessive clinker formation in gas producers is the__________?
- In furnaces operating at very high temperature (say) 1250°C, e.g. soaking pit), the maximum heat transfer takes place by__________?