A. Remove dirt
B. Increase heat transfer rate
C. Reduce vibrations
D. Reduce heat transfer rate
Submitted by: Faheem Zaman Dhaunroo
Correct Answer: Increase heat transfer rate ✔
Last Updated: July 28, 2023
Related MCQs
- Maximum heat transfer rate can be expected in case of_________?
- Pick out the correct statement ?
- Pick out the wrong statement ?
- Pick out the wrong statement?
- Pick out the wrong statement?
- Pick out the wrong statement ?
- Pick out the wrong statement/
- Pick out the wrong statement?
- Pick out the correct equation ?
- Pick out the wrong statement ?
- Pick out the correct statement ?
- Pick out the wrong statement ?
- Choose the correct equation ?
- Pick out the wrong statement ?
- Pick out the wrong statement ?
- Pick out the wrong statement ?
- Pick out the wrong statement?
- Pick out the wrong statement?
- Pick out the wrong statement?
- Pick out the wrong statement ?
- Which of the following is correct ?
- Pick out the wrong statement ?
- Pick out the wrong statement ?
- Pick out the wrong statement?
- A backward feed multiple effect evaporator is better than forward feed for concentrating cold feed, because it provides __________?
- For evaporation of viscous solution in a multiple effect evaporator, the preferred feeding scheme is __________?
- 1000 Kg of liquid at 30°C in a well stirred vessel has to be heated to 120°C, using immersed coils carrying condensing steam at 150°C. The area of the steam coils is 1.2 m2 and the overall heat transfer co-efficient to the liquid is 1500 W/m2.°C. Assuming negligible heat loss to the surrounding and specific heat capacity of the liquid to be 4 kJ/kg.°C, the time taken for the liquid to reach desired temperature will be__________?
- Heat waves__________?
- If air (a non-condensing gas) is present in a condensing vapor stream, it will __________ the condensation rate of vapor?
- For a perfectly transparent surface (like gases), the__________?
- A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter ‘d’. For a fixed mass flow rate, the tube side heat transfer co-efficient for turbulent flow conditions is proportional to__________?
- Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/μ)0.8 (CP.μ/k)0.4. This is valid for the value of NRe equal to__________?
- The ratio of kinematic viscosity to thermal diffusivity is called the __________ number?
- Vibrations in the tubes of a shell and tube heat exchanger is induced due to the __________?
- What is the steam economy in case of a single effect evaporator system ?
- For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus- Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of__________?
- Baffles in the shell side of a shell and tube heat exchanger ?
- __________ chart is known as transient heat conduction chart?
- Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer?
- Which of the following is concerned with both heat and mass transfer ?
- Duhring‟s rule is important in solving problems on__________?
- Heat transfer by radiation between two bodies at T1 & T2 and in an ambient temperature of Ta°C depends on__________?
- The film thickness for laminar film condensation on vertical surface __________ from top to bottom?
- __________ paint has the minimum absorption co-efficient?
- For shell and tube heat exchanger, with increasing heat transfer area, the purchased cost per unit heat transfer area__________?
- Mode of heat transfer in which the fluid moves under the influence of changes in fluid pressure produced by external work is called__________?
- Steam traps are provided in steam carrying pipelines to__________?
- Kirchoff‟s law applies to __________ radiation?
- Log mean temperature difference (LMTD) cannot be used, if __________?
- In a parallel flow heat exchanger, if the outlet temperature of hot and cold fluids are the same, then the log mean temperature difference (LMTD) is__________?
- Bulk of the convective heat transfer resistance from a hot tube surface to the fluid flowing in it, is __________?