A. 11.2 kW/m2
B. 12.0 kW/m2
C. 14.6 kW/m2
D. 16.5 kW/m2
Correct Answer: 16.5 kW/m2 ✔
Last Updated: March 03, 2019
Related MCQs
- A composite flat wall of a furnace is made of two materials ‘A’ and ‘B’. The thermal conductivity of ‘A’ is twice of that of material ‘B’, while the thickness of layer of ‘A’ is half that of B. If the temperature at the two sides of the wall are 400 and 1200°K, then the temperature drop (in °K) across the layer of material ‘A’ is__________?
- In forced convection, the heat transfer depends on __________?
- Kg of liquid evaporated per hour in an evaporator is defined as its__________?
- In SI units, fouling factor is expressed in __________?
- Radiation heat losses from satisfactorily insulated high pressure boiler may be about __________ percent?
- In the free convection regime of pool boiling, the heat flux is proportional to__________?
- Prandtl number is the ratio of__________?
- Prandtl number is given by__________?
- Trap is used to remove __________ from steam pipe lines?
- Wavelength corresponding to the maximum energy is inversely proportional to the absolute temperature. This is __________ law?
- Economy of a multiple effect evaporator depends upon the __________?
- A wall has two layers of materials A and B; each made of a different material. Both the layers have the same thickness. The thermal conductivity of material A is twice that of B. Under the equilibrium, the temperature difference across the wall is 36°C. The temperature difference across the layer A is __________ °C?
- Temperature profile in steady state heat transfer is__________?
- Maximum water velocity in tubes of a 1-2 shell and tube heat exchanger may be around __________ metres/second?
- A tank painted with which of the following coloured paints, would heat up maximum by radiation from sun ?
- Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface between B and C will be at a temperature of __________ °C?
- The thermal radiation emitted by a body is proportional to Tn, where T is its absolute temperature. The value of ‘n’ is exactly 4 for__________?
- Evaporation by thermo compression results in the __________?
- Use of transverse baffles in a shell and tube heat exchanger is done to increase the__________?
- Which of the following situations can be approximated to a steady state heat transfer system ?
- Heat transfer by __________ may not necessarily require the presence of a medium?
- Nusselt number is the ratio of the __________?
- Prandtl number is the reciprocal of__________?
- For a multipass shell and tube heat exchanger, the LMTD correction factor is always__________?
- Thermal conductivity of a gas at low density, __________ with increase in temperature ?
- The interchange factor for radiation heat transfer from surface ‘x’ to surface ‘y’ in case of an infinite parallel planes with emissivities εx & εy is given by__________?
- With increase in temperature, the thermal conductivity of a gas __________?
- Which area is used in case of heat flow by conduction through a cylinder ?
- The rate of emission of radiation by a body does not depend upon the__________?
- In a cooling tower, water becomes cool by__________?
- Out of the following four assumptions used in the derivation of the equation for LMTD [LMTD = (Δt1 – Δt2)/ln(Δt1/Δt2)], which one is subject to the largest deviation in practice ?
- What is the logarithmic mean of r1 and r2 ?
- The Nusselt number for fully developed (both thermally and hydrodynamically) laminar flow through a circular pipe, where the wall heat flux is constant, is__________?
- The overall resistance for heat transfer through a series of flat resistance, is the __________ of the resistances?
- Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8. Pr n, is not valid, if the value of __________?
- An ejector is used to__________?
- In a laboratory test run, the rate of drying was found to be 0.5 x 10-3 kg/m2.s, when the moisture content reduced from 0.4 to 0.1 on dry basis. The critical moisture content of the material is 0.08 on a dry basis. A tray dryer is used to dry 100 kg (dry basis) of the same material under identical conditions. The surface area of the material is 0.04 m2/kg of dry solid. The time required (in seconds) to reduce the moisture content of the solids from 0.3 to 0.2 (dry basis) is__________?
- Peclet number (Pe) is given by__________?
- In Fourier’s law, the proportionality constant is called the__________?
- When the ratio of the Grashoff number and to the square of Reynolds number is one, the dominant mechanism of heat transfer is __________?
- The units of resistance to heat transfer is __________?
- For hot feed, forward feeding as compared to backward feeding results in __________ economy?
- In sub-cooled boiling ?
- Heat transfer by conduction results due to the transfer of free electrons, kinetic energy & vibrational energy from one molecule to another. Conduction heat transfer cannot take place__________?
- The thickness of condensate layer in filmwise condensation depends on the__________?
- The heat transfer co-efficient in film type condensation is __________ that for dropwise condensation?
- Steam economy in case of a triple effect evaporator will be __________?
- In a forward feed multiple effect evaporator unit__________?
- Dropwise condensation is promoted on a/an __________ surface?
- Which of the following parameters of the fluid is not very important, while deciding its route in a shell and tube heat exchanger ?
- It is desired to concentrate a 20% salt solution (20 kg of salt in 100 kg of solution) to a 30% salt solution in an evaporator. Consider a feed of 300 kg/min at 30°C. The boiling point of the solution is 110°C, the latent heat of vaporisation is 2100 kJ/kg and the specific heat of the solution is 4 kJ/kg.K. The rate at which the heat has to be supplied in (kJ/min) to the evaporator is__________?