A. cork flooring
B. glass flooring
C. wooden flooring
D. linoleum flooring
Correct Answer: cork flooring ✔
Last Updated: January 11, 2019
Related MCQs
- The maximum total settlement for raft foundation on clayey soils should be limited to__________?
- The maximum total settlement for isolated foundations on clayey soils should be limited to__________?
- In case of foundations on black cotton soils, the most suitable method to increase the bearing capacity of soils is to__________?
- Single flemish bond consists of__________?
- Number of vertical joints in a stretcher course is x times the number of joints in the header course, where x is equal to__________?
- The slenderness ratio for masonry walls should not be more than__________?
- As compared to stretcher course, the thickness of joints in header course should be__________?
- The proportions of lime and sand in the mortar normally used in brick construction are__________?
- A mortar joint in masonry which is normal to the face of wall is known as__________?
- Expansion Joints in masonry walls are provided in wall lengths usater than__________?
- Minimum thickness of wall where single flemish bond can be used is__________?
- The type of bond provided in brick masonry for carrying heavy loads is__________?
- The most important tool in brick laying for lifting and spreading mortar and for forming joints is__________?
- Which of the following should be used for hearting of thicker walls ?
- The stretcher bond in brick masonry can be used only when the thickness of wall is__________?
- A queen closer is a__________?
- The pressure acting on the stones in stone masonry construction should be__________?
- Percentage of carbon content in mild steel is__________?
- The ratio of the thickness of web to that of flange of steel rolled structural beams and channels is__________?
- Assertion A : Paints with white lead base are not recommended for painting of iron works. Reason R : Paints with white lead base do not check rusting of iron. Select your answer according to the coding system given below ?
- Which of the following stresses is used for identifying the quality of structural steel ?
- Paints with white lead base are suitable for painting of__________?
- The vehicle used in case of enamel paints is usually__________?
- In brick masonry the bond produced by laying alternate headers and stretchers in each course is known as__________?
- The amount of water used for one kg of distemper is__________?
- Assertion A : Normally turpentine oil is recommended as thinner for indoor painting. Reason R : Turpentine oil is costlier than other thinners. Select your answer according to the coding system given below ?
- Which of the following is the purest form of iron ?
- The basic purpose of a retarder in concrete is__________?
- The most commonly used retarder in cement is__________?
- The ultimate tensile strength of structural mild steel is about__________?
- Which of the following cements contains maximum percentage of dicalcium silicate?
- Three basic raw materials which are needed in large quantities for production of steel are__________?
- Which of the following gradients exerts maximum influence on properties of steel?
- The most common admixture which is used to accelerate the initial set of concrete is__________?
- The maximum quantity of calcium chloride used as an accelerator in cement in percentage by weight of cement is__________?
- Which of the following cements is suitable for use in massive concrete structures such as large dams ?
- For testing compressive and tensile strength of cement, the cement mortar is made by mixing cement and standard sand in the proportions of__________?
- Gypsum consists of__________?
- The normal consistency of ordinary Portland cement is about__________?
- After storage, the strength of cement__________?
- The slump recommended for mass concrete is about__________?
- Addition of pozzolana to ordinary Portland cement increases__________?
- With increase in moisture content, the bulking of sand__________?
- According to IS specifications, the compressive strength of ordinary portland cement after three days should not be less than__________?
- Early attainment of strength in rapid hardening cement is mainly due to__________?
- For testing compressive strength of cement, the size of cube used is__________?
- The main constituent of cement which is responsible for initial setting of cement is__________?
- The main constituent which imparts hydraulicity to hydraulic lime is__________?
- Assertion A : Pure lime takes a long time to develop adequate strength. Reason R : Pure lime has slow hardening characteristics. Select your answer according to the coding system given below ?
- Study the following statements. (1) Hydraulic lime is suitable for white washing, (2) Fat lime is suitable for whitewashing, (3) Hydraulic lime is suitable for making mortar, (4) Fat lime is suitable for making mortar. The correct answer is__________?
- As per IS specifications, the maximum final setting time for ordinary Portland cement should be__________?