A. ultimate stress
B. yield stress
C. proof stress
D. none of the above
Correct Answer: yield stress ✔
Last Updated: January 09, 2019
Related MCQs
- Paints with white lead base are suitable for painting of__________?
- The vehicle used in case of enamel paints is usually__________?
- In brick masonry the bond produced by laying alternate headers and stretchers in each course is known as__________?
- The amount of water used for one kg of distemper is__________?
- Assertion A : Normally turpentine oil is recommended as thinner for indoor painting. Reason R : Turpentine oil is costlier than other thinners. Select your answer according to the coding system given below ?
- Which of the following is the purest form of iron ?
- The basic purpose of a retarder in concrete is__________?
- The most commonly used retarder in cement is__________?
- The ultimate tensile strength of structural mild steel is about__________?
- Which of the following cements contains maximum percentage of dicalcium silicate?
- Three basic raw materials which are needed in large quantities for production of steel are__________?
- Which of the following gradients exerts maximum influence on properties of steel?
- The most common admixture which is used to accelerate the initial set of concrete is__________?
- The maximum quantity of calcium chloride used as an accelerator in cement in percentage by weight of cement is__________?
- Which of the following cements is suitable for use in massive concrete structures such as large dams ?
- For testing compressive and tensile strength of cement, the cement mortar is made by mixing cement and standard sand in the proportions of__________?
- Gypsum consists of__________?
- The normal consistency of ordinary Portland cement is about__________?
- After storage, the strength of cement__________?
- The slump recommended for mass concrete is about__________?
- Addition of pozzolana to ordinary Portland cement increases__________?
- With increase in moisture content, the bulking of sand__________?
- According to IS specifications, the compressive strength of ordinary portland cement after three days should not be less than__________?
- Early attainment of strength in rapid hardening cement is mainly due to__________?
- For testing compressive strength of cement, the size of cube used is__________?
- The main constituent of cement which is responsible for initial setting of cement is__________?
- The main constituent which imparts hydraulicity to hydraulic lime is__________?
- Assertion A : Pure lime takes a long time to develop adequate strength. Reason R : Pure lime has slow hardening characteristics. Select your answer according to the coding system given below ?
- Study the following statements. (1) Hydraulic lime is suitable for white washing, (2) Fat lime is suitable for whitewashing, (3) Hydraulic lime is suitable for making mortar, (4) Fat lime is suitable for making mortar. The correct answer is__________?
- As per IS specifications, the maximum final setting time for ordinary Portland cement should be__________?
- The constituent of cement which is responsible for all the undesirable properties of cement is__________?
- The initial setting time for ordinary Portland cement as per IS specifications should not be less than__________?
- Le Chatelier’s device is used for determining the__________?
- The main ingredients of Portland cement are__________?
- Hydraulic lime is obtained by__________?
- Glazing is used to make earthenware__________?
- Quick lime is (1) slow in setting (2) rapid in slacking (3) good in strength The correct answer is__________?
- Quick lime is__________?
- Number of bricks required for one cubic metre of brick masonry is__________?
- Advantage of a clamp compared to a kiln for burning bricks is that__________?
- The frog of the brick in a brick masonry is generally kept on__________?
- Which of the following pairs gives a correct combination of the useful and harmful constituents respectively of a good brick earth ?
- Pug mill is used for__________?
- Which of the following bricks are used for lining of furnaces ?
- The internal size of mould used in brick preparation is__________?
- The process of mixing clay, water and other ingredients to make brick is known as__________?
- Which of the following ingredients of the brick earth enables the brick to retain its shape ?
- Excess of silica in brick earth results in__________?
- The nominal size of the modular brick is__________?
- The percentage of alumina in a good brick earth lies between__________?
- Percentage of silica in a good brick earth lies between__________?