A. bending moment and shear
B. bending moment and torsion
C. shear and torsion
D. bending moment, shear and torsion
Correct Answer: shear and torsion ✔
Last Updated: January 12, 2019
Related MCQs
- Due to shrinkage stresses, a simply supported beam having reinforcement only at bottom tends to__________?
- As per Whitney’s theory, the maximum moment of resistance of the balanced section of a beam of width b and effective depth d is given by__________?
- According to Whitney’s theory, depth of stress block for a balanced section of a concrete beam is limited to__________?
- The design yield stress of steel according to IS: 456-1978 is__________?
- Assertion A : The load factor for live load is greater than that for dead load. Reason R : The live loads are more uncertain than dead loads?
- According to Whitney’s theory, ultimate strain of concrete is assumed to be__________?
- The load factors for live load and dead load are taken respectively as__________?
- The centroid of compressive force, from the extreme compression fiber, in limit state design lies at a distance of__________?
- According to ISI recommendations, the maximum depth of stress block for balanced section of a beam of effective depth d is__________?
- During erection, the pile of length / is supported by a crane at a distance of__________?
- If the foundations of all the columns of a structure are designed on the total live and dead load basis, then__________?
- The critical section for finding maximum bending moment for footing under masonry wall is located__________?
- While designing the pile as a column, the end conditions are nearly__________?
- In a pile of length /, the points of suspension from ends for lifting it are located at__________?
- To minimise the effect of differential settlement, the area of a footing should be designed for__________?
- A T-shaped retaining wall mainly conssits of__________?
- In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on__________?
- In counterfort retaining walls, the main reinforcement in the stem at support is__________?
- The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on__________?
- For a reinforced concrete section, the shape of shear stress diagram is__________?
- If nominal shear stress tv exceeds the design shear strength of concrete xc, the nominal shear reinforcement as per IS : 456-1978 shall be provided for carrying a shear stress equal to__________?
- If the depth of neutral axis for a singly reinforced rectangular section is represented by kd in working stress design, then the value of k for balanced section__________?
- Modulus of elasticity of steel as per IS : 456-1978 shall be taken as__________?
- For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine’s theory__________?
- The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is__________?
- Which of the following R.C. retaining walls is suitable for heights beyond 6m ?
- Due to circumferential action of the spiral in a spirally reinforced column__________?
- The load carrying capacity of a helically reinforced column as compared to that of a tied column is about__________?
- For the design of retaining walls, the minimum factor of safety against overturning is taken as__________?
- The minimum diameter of longitudinal bars in a column is__________?
- The diameter of ties in a column should be__________?
- Maximum percentage reinforcement in case of slabs is limited to__________?
- The minimum cover to the ties or spirals should not be less than__________?
- The limits of percentage p of the longitudinal reinforce-ment in a column is given by__________?
- The main reason for providing number of reinforcing bars at a support in a simply supported beam is to resist in that zone__________?
- When shear stress exceeds the permissible limit in a slab, then it is reduced by__________?
- The permissible diagonal tensile stress in reinforced brick work is__________?
- If the size of panel in a flat slab is 6m x 6m, then as per Indian Standard Code, the widths of column strip and middle strip are__________?
- Half of the main steel in a simply supported slab is bent up near the support at a distance of x from the center of slab bearing where x is equal to__________?
- In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by__________?
- Ratio of permissible stress in direct compression and bending compression is__________?
- A higher modular ratio shows__________?
- Maximum distance between expansion joints in structures as per IS : 456 – 1978 is__________?
- The average permissible stress in bond for plain bars in tension is__________?
- Critical section for shear in case of flat slabs is at a distance of__________?
- If the storey height is equal to length of RCC wall, the percentage increase in strength is__________?
- The slab is designed as one way if the ratio of long span to short span is__________?
- In reinforced concrete footing on soil, the minimum thickness at edge should not be less than__________?
- Minimum thickness of load bearing RCC wall should be__________?
- A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (1/D. is less than__________?
- Minimum pitch of transverse reinforcement in a column is__________?