1. maximum bending moment
2. shear force
3. punching shear
The correct answer is?
A. only (1)
B. (1) and (2)
C. (1) and (3)
D. (1), (2) and (3)
Correct Answer: 1. maximum bending moment ✔
Last Updated: January 12, 2019
Related MCQs
- Select the correct statement?
- Select the incorrect statement?
- In a ring beam subjected to uniformly distributed load__________?
- Sinking of an intermediate support of a continuous beam__________?
- Shrinkage of concrete depends upon__________?
- In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on__________?
- In a counterfort retaining wall, the main reinforcement is provided on the__________?
- The main reinforcement in the toe of a T- shaped R C. retaining wall is provided on__________?
- In counterfort type retaining walls__________?
- Examine the following statements __________?
- The effect of adding calcium chloride in concrete is__________?
- Select the incorrect statement?
- Select the correct statement?
- In T-shaped R C. retaining walls, the main reinforcement in the stem is provided on__________?
- The recommended value of modular ratio for reinforced brick work is__________?
- The effect of creep on modular ratio is__________?
- In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively__________?
- In a spherical dome subjected to concentrated load at crown or uniformly distributed load, the meridional force is always__________?
- The maximum value of hoop compression in a dome is given by__________?
- The purpose of reinforcement in prestressed concrete is__________?
- Most common method of prestressing used for factory production is__________?
- Prestress loss due to friction occurs__________?
- High carbon content in the steel causes__________?
- Ultimate strength of cold drawn high steel wires__________?
- Cube strength of controlled concrete to be used for pretensioned and post-tensioned work respectively should not be less than__________?
- Stress strain curve of high tensile steel__________?
- Which of the following has high tensile strength ?
- Which of the following losses of prestress occurs only in pretensioning and not in post-tensioning ?
- Normally prestressing wires are arranged in the__________?
- In prestressed concrete__________?
- In a spherical dome the hoop stress due to a concentrated load at crown is__________?
- A beam curved in plan is designed for__________?
- Due to shrinkage stresses, a simply supported beam having reinforcement only at bottom tends to__________?
- As per Whitney’s theory, the maximum moment of resistance of the balanced section of a beam of width b and effective depth d is given by__________?
- According to Whitney’s theory, depth of stress block for a balanced section of a concrete beam is limited to__________?
- The design yield stress of steel according to IS: 456-1978 is__________?
- Assertion A : The load factor for live load is greater than that for dead load. Reason R : The live loads are more uncertain than dead loads?
- According to Whitney’s theory, ultimate strain of concrete is assumed to be__________?
- The load factors for live load and dead load are taken respectively as__________?
- The centroid of compressive force, from the extreme compression fiber, in limit state design lies at a distance of__________?
- According to ISI recommendations, the maximum depth of stress block for balanced section of a beam of effective depth d is__________?
- During erection, the pile of length / is supported by a crane at a distance of__________?
- If the foundations of all the columns of a structure are designed on the total live and dead load basis, then__________?
- The critical section for finding maximum bending moment for footing under masonry wall is located__________?
- While designing the pile as a column, the end conditions are nearly__________?
- In a pile of length /, the points of suspension from ends for lifting it are located at__________?
- To minimise the effect of differential settlement, the area of a footing should be designed for__________?
- A T-shaped retaining wall mainly conssits of__________?
- In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on__________?
- In counterfort retaining walls, the main reinforcement in the stem at support is__________?
- The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on__________?