A. 5% less
B. 10% less
C. 5% more
D. 10% more
Correct Answer: 5% more ✔
Last Updated: January 12, 2019
Related MCQs
- For the design of retaining walls, the minimum factor of safety against overturning is taken as__________?
- The minimum diameter of longitudinal bars in a column is__________?
- The diameter of ties in a column should be__________?
- Maximum percentage reinforcement in case of slabs is limited to__________?
- The minimum cover to the ties or spirals should not be less than__________?
- The limits of percentage p of the longitudinal reinforce-ment in a column is given by__________?
- The main reason for providing number of reinforcing bars at a support in a simply supported beam is to resist in that zone__________?
- When shear stress exceeds the permissible limit in a slab, then it is reduced by__________?
- The permissible diagonal tensile stress in reinforced brick work is__________?
- If the size of panel in a flat slab is 6m x 6m, then as per Indian Standard Code, the widths of column strip and middle strip are__________?
- Half of the main steel in a simply supported slab is bent up near the support at a distance of x from the center of slab bearing where x is equal to__________?
- In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by__________?
- Ratio of permissible stress in direct compression and bending compression is__________?
- A higher modular ratio shows__________?
- Maximum distance between expansion joints in structures as per IS : 456 – 1978 is__________?
- The average permissible stress in bond for plain bars in tension is__________?
- Critical section for shear in case of flat slabs is at a distance of__________?
- If the storey height is equal to length of RCC wall, the percentage increase in strength is__________?
- The slab is designed as one way if the ratio of long span to short span is__________?
- In reinforced concrete footing on soil, the minimum thickness at edge should not be less than__________?
- Minimum thickness of load bearing RCC wall should be__________?
- A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (1/D. is less than__________?
- Minimum pitch of transverse reinforcement in a column is__________?
- Which of the following statements is incorrect ?
- According to IS: 456-1978, the maximum reinforcement in a column is__________?
- According to IS : 456-1978, the fiexural strength of concrete is__________?
- Lap length in compression shall not be less than__________?
- For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than__________?
- The percentage of reinforcement in case of slabs, when high strength deformed bars are used is not less than__________?
- The ratio of the diameter of reinforcing bars and the slab thickness is__________?
- The minimum cover in a slab should neither be less than the diameter of bar nor less than__________?
- According to IS : 456- 1978, minimum slenderness ratio for a short column is__________?
- For a simply supported beam of span 15m, the minimum effective depth to satisfy the vertical deflection limits should be__________?
- According to IS : 456-1978, the cblumn or the strut is the member whose effective length is greater than__________?
- Diagonal tension in a beam__________?
- For a cantilever of effective depth of 0.5m, the maximum span to satisfy vertical deflection limit is__________?
- For a continuous slab of 3 m x 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is__________?
- One of the criteria for the effecvve width of flange of T-beam is bf =—+ bw +6Df 6 In above formula, l0 signifies__________?
- For walls, columns and vertical faces of all structural members, the form work is generally removed after__________?
- For walls, columns and vertical faces of all structural members, the form work is generally removed after__________?
- The individual variation between test strength of sample should not be more than__________?
- In case of hand mixing of concrete, the extra cement to be added is__________?
- For concreting of heavily reinforced sections without vibration, the workability of concrete expressed as compacting factor should be__________?
- Maximum quantity of water needed per 50 kg of cement for M 15 grade of concrete is__________?
- Minimum grade of concrete to be used in reinforced concrete as per IS:456-1978 is__________?
- If the permissible stress in steel in tension is 140 N/mm2, then the depth of neutral axis for a singly reinforced rectangular balanced section will be__________?
- If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called__________?
- If a beam fails in bond, then its bond strength can be increased most economi-cally by__________?
- The compressive strength of 100 mm cube as compared to 150 mm cube is always__________?
- The fineness modulus of fine aggregate is in the range of__________?
- The factor of safety for__________?