A. less than 1
B. between 1 and 1.5
C. between 1.5 and 2
D. greater than 2
Correct Answer: greater than 2 ✔
Last Updated: January 12, 2019
Related MCQs
- In reinforced concrete footing on soil, the minimum thickness at edge should not be less than__________?
- Minimum thickness of load bearing RCC wall should be__________?
- A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (1/D. is less than__________?
- Minimum pitch of transverse reinforcement in a column is__________?
- Which of the following statements is incorrect ?
- According to IS: 456-1978, the maximum reinforcement in a column is__________?
- According to IS : 456-1978, the fiexural strength of concrete is__________?
- Lap length in compression shall not be less than__________?
- For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than__________?
- The percentage of reinforcement in case of slabs, when high strength deformed bars are used is not less than__________?
- The ratio of the diameter of reinforcing bars and the slab thickness is__________?
- The minimum cover in a slab should neither be less than the diameter of bar nor less than__________?
- According to IS : 456- 1978, minimum slenderness ratio for a short column is__________?
- For a simply supported beam of span 15m, the minimum effective depth to satisfy the vertical deflection limits should be__________?
- According to IS : 456-1978, the cblumn or the strut is the member whose effective length is greater than__________?
- Diagonal tension in a beam__________?
- For a cantilever of effective depth of 0.5m, the maximum span to satisfy vertical deflection limit is__________?
- For a continuous slab of 3 m x 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is__________?
- One of the criteria for the effecvve width of flange of T-beam is bf =—+ bw +6Df 6 In above formula, l0 signifies__________?
- For walls, columns and vertical faces of all structural members, the form work is generally removed after__________?
- For walls, columns and vertical faces of all structural members, the form work is generally removed after__________?
- The individual variation between test strength of sample should not be more than__________?
- In case of hand mixing of concrete, the extra cement to be added is__________?
- For concreting of heavily reinforced sections without vibration, the workability of concrete expressed as compacting factor should be__________?
- Maximum quantity of water needed per 50 kg of cement for M 15 grade of concrete is__________?
- Minimum grade of concrete to be used in reinforced concrete as per IS:456-1978 is__________?
- If the permissible stress in steel in tension is 140 N/mm2, then the depth of neutral axis for a singly reinforced rectangular balanced section will be__________?
- If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called__________?
- If a beam fails in bond, then its bond strength can be increased most economi-cally by__________?
- The compressive strength of 100 mm cube as compared to 150 mm cube is always__________?
- The fineness modulus of fine aggregate is in the range of__________?
- The factor of safety for__________?
- Poisson’s ratio for concrete__________?
- Finer grinding of cement__________?
- 1% of voids in a concrete mix would reduce its strength by about__________?
- Bulking of sand is maximum if moisture content is about__________?
- As compared to ordinary portland cement, high alumina cement has__________?
- In order to obtain the best workability of concrete, the preferred shape of aggregate is__________?
- Modulus of rupture of concrete is a measure of__________?
- The percentage of voids in cement is approximately__________?
- To determine the modulus of rupture, the size of test specimen used is__________?
- The property of fresh concrete, in which the water in the mix tends to rise to the surface while placing and compacting, is called__________?
- Workability of concrete is inversely pro¬portional to__________?
- Air entrainment in the concrete increases__________?
- The approximate value of the ratio between direct tensile strength and flexural strength is__________?
- The relation between modulus of rupturefcr and characteristic strength of concrete fck is given by__________?
- Increase in the moisture content in concrete__________?
- Admixtures which cause early setting, and hardening of concrete are called__________?
- The strength of concrete after one year as compared to 28 days strength is about__________?
- The most commonly used admixture which prolongs the setting and hardening time is__________?
- According to IS : 456 -1978, the modulus of elasticity of concrete Ec (in N/mm2) can be taken as__________?