A. 1.0
B. 2.0
C. 0.5
D. 10
Correct Answer: 1.0 ✔
Last Updated: January 12, 2019
Related MCQs
- Which of the following is known as design capacity ?
- The diagram which shows the approximate path of vehicles and pedestrians involved in accidents is known as__________?
- Desire lines are plotted in__________?
- Length of a vehicle affects__________?
- Which of the following methods is preferred for collecting origin and destination data for a small area like a mass business center or a large intersection ?
- Select the correct statement__________?
- The maximum width of a vehicle as recommended by IRC is__________?
- For highway geometric design purposes the speed used is__________?
- Highway facilities are designed for__________?
- If the design speed is V kmph and deviation angle is N radians, then the total length of a valley curve in meters is given by the expression__________?
- The value of ruling gradient in plains as per IRC recommendation is__________?
- If an ascending gradient of 1 in 50 meets a descending gradient of 1 in 50, the length of summit curve for a stopping sight distance of 80 m will be__________?
- Enoscope is used to find__________?
- In case of summit curves, the deviation angle will be maximum when__________?
- The camber of road should be approximately equal to__________?
- The percentage compensation in gradient for ruling gradient of 4% and horizontal curve of radius 760 m is__________?
- Which of the following shapes is preferred in a valley curve ?
- If ruling gradient is I in 20 and there is also a horizontal curve of radius 76 m, then the compensated grade should be__________?
- For design, that length of transition curve should be taken which is__________?
- Select the correct statement__________?
- The absolute minimum radius of curve for safe operation for a speed of 110 kmph is__________?
- The transition curve used in the horizontal alignment of highways as per IRC recommendations is__________?
- The maximum design gradient for vertical profile of a road is__________?
- In case of hill roads, the extra widening is generally provided__________?
- To calculate the minimum value of ruling radius of horizontal curves in plains, the design speed is given by__________?
- The attainment of super elevation by rotation of pavement about the inner edge of the pavement__________?
- On a horizontal curve if the pavement is kept horizontal across the alignment, then the pressure on the outer wheels will be__________?
- As per IRC recommendations, the maximum limit of super elevation for mixed traffic in plain terrain is__________?
- For a constant value of coefficient of lateral friction, the value of required super-elevation increases with__________?
- For the design of super elevation for mixed traffic conditions, the speed is reduced by__________?
- The terrain may be classified as rolling terrain if the cross slope of land is__________?
- Stopping sight distance is always__________?
- The effect of grade on safe overtaking sight distance is__________?
- The ruling design speed on a National Highway in plain terrain as per IRC recommendations is__________?
- If b is the wheel track of a vehicle and h is the height of centre of gravity above road surface, then to avoid overturning and lateral skidding on a horizontal curve, the centrifugal ratio should always be__________?
- If the stopping distance is 60 meters, then the minimum stopping sight distance for two lane, two way traffic is__________?
- Reaction time of a driver__________?
- Select the correct statement__________?
- The desirable length of overtaking zone as per IRC recommendation is equal to__________?
- Compared to a level surface, on a descending gradient the stopping sight distance is__________?
- Nagpur road plan formula were prepared by assuming__________?
- The sequence of four stages of survey in a highway alignment is__________?
- For water bound macadam roads in localities of heavy rainfall, the recommended value of camber is__________?
- When the path travelled along the road surface is more than the circumferential movement of the wheels due to rotation, then it results in__________?
- The shoulder provided along the road edge should be__________?
- On a single lane road with two way traffic, the minimum stopping sight distance is equal to__________?
- Camber in the road is provided for__________?
- Coefficient of friction is less when the pavement surface is__________?
- The stopping sight distance depends upon__________?
- The shape of the camber, best suited for cement concrete pavements, is__________?