A. 100 W
B. 500 W
C. 1000 W
D. 1500 W
Correct Answer: 500 W ✔
Last Updated: July 02, 2018
Related MCQs
- Which of the following losses are significantly reduced by laminating the core of a D.C. generator ?
- Which of the following loss in a D.C. generator is dissipated in the form of heat?
- Which of the following steps is likely to result in reduction of hysteresis loss in a D.C. generator ?
- In a manual shunt motor starter?
- D.C. shunt motors are used for driving__________?
- Torque developed by a D.C. motor depends upon__________?
- Which of the following loss in a D.C. generator varies significantly with the load current ?
- The losses occurring in a D.C. generator are given below. Which loss is likely to have highest proportion at rated load of the generator ?
- In a D.C. generator all of the following could be the effects of iron losses except__________?
- The hysteresis loss in a D.C. machine least depends on__________?
- Regenerative method of braking is based on that__________?
- The main disadvantage of the Ward-Leonard control method is__________?
- In Ward-Leonard control the lower limit of speed is imposed by________?
- For constant torque drive which speed control method is preferred ?
- Ward-Leonard control is basically a__________?
- Which motor should not be started on no-load ?
- Which of the following motors is most suitable for signalling devices and many kinds of timers ?
- Which of the following motors is usually used in house-hold refrigerators ?
- Why are the D.C. motors preferred for traction applications ?
- If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will_________?
- Which of the following motors one will choose to drive the rotary compressor ?
- If the terminals of armature of D.C. motor are interchanged, this action will offer following kind of braking?
- If a D.C. motor designed for 40°C ambient temperature is to be used for 50°C ambient temperature, then the motor__________?
- The armature voltage control of D.C. motor provides__________?
- The plugging gives the__________?
- For a D.C. shunt motor if the excitation is changed__________?
- Which motor has the poorest speed control?
- If I2 be the armature current, then speed of a D.C. shunt motor is__________?
- The speed of a D.C. shunt motor can be increased by__________?
- As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit__________?
- The armature voltage control of D.C. motor provides__________?
- The speed of a motor falls from 1100 r.p.m. at no-load to 1050 r.p.m. at rated load. The speed regulation of the motor is__________?
- Usually wide and sensitive speed control is desired in case of__________?
- Which of the following method of speed control of D.C. machine will offer minimum efficiency ?
- The armature torque of the D.C. shunt motor is proportional to__________?
- As -the load is increased the speed of D.C. shunt motor will__________?
- Which of the following motor has the poorest speed regulation ?
- Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of__________?
- In a differentially compounded D.C. motor, if shunt field suddenly opens__________?
- Following motor is used where high starting torque and wide speed range control is required?
- Flywheel is used with D.C. compound motor to reduce the peak demand by the motor, compound motor will have to be__________?
- Speed control by Ward Leonard method gives uniform speed variation__________?
- Sparking, is discouraged in a D.C. motor because__________?
- Three point starter can be used for__________?
- Which D.C. motor is generally preferred for cranes and hoists ?
- In D.C. machines the residual magnetism is of the order of__________?
- For which of the following applications a D.C. motor is preferred over an A.C. motor ?
- The condition for maximum power in case of D.C. motor is__________?
- The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is__________?
- Which one of the following is not the function of pole shoes in a D.C. machine ?
- If the supply voltage for a D.C. motor is increased, which of the following will decrease ?