A. short pitch
B. full pitch
C. either of the above
D. none of the above
Correct Answer: full pitch ✔
Last Updated: December 22, 2018
Related MCQs
- The distance between the starts of two consecutive coils measured in terms of coil sides is called__________?
- Dummy coil should not be used in__________?
- Power transformers should be designed to have maximum efficiency__________?
- Yokes with rectangular cross-section are used for__________?
- Which of the following methods is most accurate ?
- __________are used for construction of core of electromagnets?
- Tractive magnets are operated from__________?
- Which of the following is the commonly used type of electromagnets ?
- The design of electromagnets is based upon which of the following fundamental equations ?
- electromagnets generally function as holding magnets ?
- By which of the following methods motor rating for variable load drives can be determined ?
- The value of exciting or magnetizing current depends upon which of the following factors ?
- By which of the following methods the temperature rise of windings and other parts may be determined ?
- Which of the following methods is used for air cooling of turbo-alternators ?
- The slot leakage can be calculated by making which of the following assumptions ?
- Which of the following methods does not take into account the maximum temperature rise under variable load conditions ?
- The time taken by the machine to attain 0.632 of its final steady temperature rise is called__________?
- With direct water cooling it is possible to have ratings of about__________?
- In self cooled motors the cooling time constant is about __________ than the heating time constant because cooling conditions are worse at standstill?
- Direct water cooling of rotor winding presents__________?
- In direct cooled system using hydrogen both stator and rotor conductors are made__________?
- The resistivity of water should not be less than__________?
- Machines cooled by direct cooling method may be called__________?
- The density of hydrogen is __________ times the density of air?
- Which of the following is an advantage of hydrogen cooling ?
- The heated parts of an electrical machine dissipate heat into their surroundings by which of the following modes of heat dissipation ?
- The noise produced by a __________ cooled machine is less as the rotor moves in a medium of smaller density?
- The thermal conductivity of hydrogen is __________ times that of air?
- cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall__________?
- With conventional hydrogen cooling it is possible to increase the rating of a single unit to__________?
- Hydrogen has a heat transfer co-efficient __________ times that of air?
- Multiple inlet system of air cooling of turbo-alternators can be used for machines of rating upto__________?
- The mcrease in heat dissipation by air blasts is due to increase in__________?
- On which of the following variables heat convected depends ?
- Which of the following materials is used in the manufacture of resistance grids to be used in the starters of large motors ?
- The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc?
- __________is extensively used for those portions of magnetic circuit which carry steady flux and need superior mechanical properties ?
- Aluminium when adopted as a conductor material in __________ transformers, decreases the overall cost of the transformer?
- Hot rolled sheets have __________ value of permeability?
- Materials exhibiting zero value of resistivity are known as __________ ?
- __________is universally used for windings of electrical machines because it is easily workable without any possibility of fracture?
- __________ has a low relative permeability and is used principally in field frames when cost is of primary importance and extra weight is not objectionable?
- Commercial available medium size machines have a speed range of __________ ?
- The change in flux linkages can be caused in which of the following ways ?
- The action of electromagnetic machines can be related to which of the following basic principles __________?
- The length cf air gap to be provided in __________ is primarily determined by power factor consideration?
- The design of mechanical parts is particularly important in case of __________ speed machines?
- impose limitation on design__________?
- If an insulating material is operated beyond the maximum allowable temperature, its life is__________?
- Electrical machines having a power output up to about 750 W may be called__________machines?
- In induction motors, the length of air gap in kept as small as mechanically possible is order to have__________?