A. Increased I R losses
B. Increased core losses
C. Poor commutation
D. Change in motor parameters
E. All of the above
Correct Answer: All of the above ✔
Last Updated: December 22, 2018
Related MCQs
- In a D.C. machine the number of brush arms is _________ the number of poles?
- D.C. machines designed with a large value of air gap length have__________?
- In D.C. machines the usual limit of slot pitch is__________?
- The operation of a D.C. machine with large air gap lengths is comparatively__________?
- In D.C. machines, ir order to prevent excessive distortion of field form by the armature reaction, the field mmf must be made__________?
- In a D.C. machine, the value of peripheral speed should not, normally, exceed__________?
- The weight of copper of both armature and field windings decreases with __________ in number of poles?
- In a D.C. machine the current per brush arm should not be more than__________?
- In D.C. machines the width of the duct is usually__________?
- In D.C. machines, the ________ in field mmf results in increase in size and cost of machines?
- Which of the following methods may be adopted to reduce the effects of armature reaction ?
- In D.C. machines the number of slots per pole usually lies__________?
- In transformers using hot rolled steel, the cross-section of the yoke is made about __________ greater than that of the core?
- Power transformers have rating__________?
- __________are always double layer type?
- The winding where dummy coils are used is sometimes called__________?
- When the two coil sides forming a coil are spaced exactly one pole pitch apart they are said to be of__________?
- The distance between the starts of two consecutive coils measured in terms of coil sides is called__________?
- Dummy coil should not be used in__________?
- Power transformers should be designed to have maximum efficiency__________?
- Yokes with rectangular cross-section are used for__________?
- Which of the following methods is most accurate ?
- __________are used for construction of core of electromagnets?
- Tractive magnets are operated from__________?
- Which of the following is the commonly used type of electromagnets ?
- The design of electromagnets is based upon which of the following fundamental equations ?
- electromagnets generally function as holding magnets ?
- By which of the following methods motor rating for variable load drives can be determined ?
- The value of exciting or magnetizing current depends upon which of the following factors ?
- By which of the following methods the temperature rise of windings and other parts may be determined ?
- Which of the following methods is used for air cooling of turbo-alternators ?
- The slot leakage can be calculated by making which of the following assumptions ?
- Which of the following methods does not take into account the maximum temperature rise under variable load conditions ?
- The time taken by the machine to attain 0.632 of its final steady temperature rise is called__________?
- With direct water cooling it is possible to have ratings of about__________?
- In self cooled motors the cooling time constant is about __________ than the heating time constant because cooling conditions are worse at standstill?
- Direct water cooling of rotor winding presents__________?
- In direct cooled system using hydrogen both stator and rotor conductors are made__________?
- The resistivity of water should not be less than__________?
- Machines cooled by direct cooling method may be called__________?
- The density of hydrogen is __________ times the density of air?
- Which of the following is an advantage of hydrogen cooling ?
- The heated parts of an electrical machine dissipate heat into their surroundings by which of the following modes of heat dissipation ?
- The noise produced by a __________ cooled machine is less as the rotor moves in a medium of smaller density?
- The thermal conductivity of hydrogen is __________ times that of air?
- cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall__________?
- With conventional hydrogen cooling it is possible to increase the rating of a single unit to__________?
- Hydrogen has a heat transfer co-efficient __________ times that of air?
- Multiple inlet system of air cooling of turbo-alternators can be used for machines of rating upto__________?
- The mcrease in heat dissipation by air blasts is due to increase in__________?
- On which of the following variables heat convected depends ?