A. a higher impedance
B. a smaller bandwidth
C. a higher resonant frequency
D. a larger bandwidth
Correct Answer: a larger bandwidth ✔
Last Updated: July 30, 2021
Related MCQs
- In a certain low-pass filter, fc = 3.5 kHz.if the input voltage is a 6 V sine wave with a dc level of 10 V, what is the output voltage magnitude?
- A parallel resonant band-pass filter consists of a 90 Ω resistor in series with a parallel network made up of a 60 mH coil and a 0.02 µF capacitor. The output is taken across the capacitor/coil. The coil winding has a resistance of 20 Ω. What is the center frequency of the filter?
- An RL high-pass filter consists of a 470 Ω resistor and a 600 mH coil. The output is taken across the coil. The circuit’s critical frequency is__________?
- An RC low-pass filter consists of a 120 Ω resistor and a 0.002 µF capacitor. The output is taken across the capacitor. The circuit’s critical frequency is__________?
- In a certain low-pass filter, fc = 3.5 kHz. Its pass-band is__________?
- An RC high-pass filter consists of an 820 Ω resistor. What is the value of C so that Xc is ten times less than Rat an input frequency of 12 kHz?
- The maximum output voltage of a certain low-pass filter is 15 V. The output voltage at the critical frequency is__________?
- The same signal in Problem 2 is applied to an RC high-pass filter. If the reactance is zero at the input frequency, the output voltage is__________?
- A sinusoidal voltage with a peak-to-peak value of 18 V is applied to an RC low-pass filter. If the reactance at the input frequency is zero, the output voltage is__________?
- Vout = 500 mV, and Vin = 1.3 V. The ratio Vout/ Vin expressed in dB is__________?
- A parallel resonant band-pass filter consists of a 6.8 Ω resistor in series with a parallel network made up of an 8 µH coil and a 120 pF capacitor. The output is taken across the capacitor/coil. Assume RW = 0 Ω. What is the center frequency of the filter?
- In a certain low-pass filter, fc = 3.5 kHz. If the input voltage is a 6 V sine wave with a dc level of 10 V, what is the output voltage magnitude?
- An RL low-pass filter consists of a 5.6 mH coil and a 3.3 kΩ resistor. The output voltage is taken across the resistor. The circuit’s critical frequency is__________?
- An RC high-pass filter consists of a 0.2 µF capacitor and a 220 Ω resistor. The output is taken across the resistor. The circuit’s critical frequency is__________?
- At a certain frequency, the output voltage of a filter is 6 V and the input is 12 V. The voltage ratio in decibels is__________?
- A series resonant band-pass filter consists of a 2 mH coil, a 0.005 µF capacitor, and a 120 Ω resistor. The winding resistance of the coil is 12 Ω. The output voltage is taken off the resistor. Input voltage is 12 Vrms. What is the output voltage magnitude at the center frequency (f0)?
- A series resonant band-stop filter consists of a 68 Ω resistor, a 110 mH coil, and a 0.02 µF capacitor. The internal resistance, RW, of the coil is 4 Ω. Input voltage is 200 mV. Output voltage is taken across the coil and capacitor in series. What is the output voltage magnitude at f0?
- In a certain low-pass filter, fc = 3.5 kHz. Its passband is__________?
- In a certain parallel resonant band-pass filter, the resonant frequency is 14 kHz. If the bandwidth is 4 kHz, the lower frequency__________?
- At a certain frequency, the output voltage of a filter is 6 V and the input is 12 V.the filter’s bandwidth is__________?