A. high h.p. and low weight
B. low weight and small frontal area
C. small frontal area and high h.p.
D. high speed and high h.p.
E. all of the above
Correct Answer: low weight and small frontal area ✔
Last Updated: January 24, 2019
Related MCQs
- Producer gas is produced by__________?
- For an irreversible gas turbine cycle, the efficiency and work ratio both depend on__________?
- It is not possible to use closed gas turbine cycle in aeronautical engines because__________ ?
- As the turbine inlet temperature increases, the thermal efficiency of gas turbine for the optimum pressure ratio__________?
- The jnaximum combustion pressure in gas turbine as compared to I.C. engine is__________?
- The material commonly used for air craft gas turbine is__________?
- The ideal efficiency of simple gas turbine cycle depends on__________?
- There is a certain pressure ratio (optimum) for a gas turbine at which its thermal efficiency is maximum. With increase in turbine temperature, the value of pressure ratio for the peak efficiency would__________?
- The combustion efficiency of a gas turbine using perfect combustion chamber is of the order of__________?
- Water gas is produced by __________ ?
- The thermal efficiency of a simple gas turbine for a given turbine inlet temperature with increase in pressure ratio__________?
- The following is true for an open cycle gas turbine having exhaust heat exchanger. Atmospheric air before entering the compressor is__________?
- Efficiency of gas turbine is increased by__________ ?
- The hottest point in a gas turbine is__________?
- Temperature of gases at end of compression as compared to exhaust gases in a gas turbine is__________?
- The pressure ratio in gas turbines is of the order of__________?
- The ratio of specific weighf/h.p. of gas turbin and I.C engines may be typically of the order of__________?
- The thermal efficiency of a gas turbine as compared to a diesel plant is__________?
- Gas turbine blades are given a rake__________?
- The air-fuel ratio in gas turbines is of the order of __________?
- Mechanical efficiency of gas turbines as compared to I.C engines is__________?
- The fuel consumption in gas turbines is accounted for by__________?
- The pressure ratio for an open cycle gas turbine compared to closed cycle gas turbine of same h.p. is__________?
- The work ratio of a gas turbine plant is defined as the ratio of__________?
- Rotary compressors are suitable for __________?
- Gas turbine works on__________?
- Gas turbine works on__________?
- The pressure ratio of an ideal vaned compressor with increase in mass flow rate__________?
- Actual compression curve is__________?
- The ratio of the increase in pressure in rotor blades to total increase in pressure in the stage is called__________?
- Surging phenomenon in centrifugal com-pressor depends on __________?
- Gas turbines for power generaion are normally used__________?
- Open cycle gas turbine works on__________?
- The work ratio of simple gas turbine cycle depends on__________?
- The vloumetric efficiency of compressor with increase in compression ratio will __________?
- Axial flow compressor resembles__________ ?
- Atmospheric pressure is 1.03 kg/cm and vapour pressure is 0.03 kg/cm . The air pressure will be__________ ?
- Axial flow compressor has the following advantage over centrifugal compressor__________?
- Maximum delivery pressure is a rotary air compressor is of the order of__________?
- The thermodynamic efficiency of rotary compressor is based on__________?
- Surging is the phenomenon of__________?
- The maximum compression ratio in an actual single stage axial flow comperssor is of the order of__________?
- The ratio of isentropic work to euler’s work is known as __________?
- The ratio of outlet whirl velocity to blade velocity in case of centrifugal compressor is called__________?
- More than one stage will be preferred for reciprocating compressor if the delivery pressure is more than__________?
- Pick up the wrong statement about advantages of multistage compression__________?
- Losses in a centrifugal compressor are due to__________?
- For a two stage compressor* if index of compression for higher stage is greater than index of compression for lower stage, then the optimum pressure as compared to ideal case will__________?
- The criterion of the thermodynamic efficiency for rotary compressor is__________?
- The volumetric efficiency of a compressor falls roughly as follows for every 5°C increase in atmospheric temperature__________?
- For minimum work in multistage compression, assuming same index of compression in all stages__________?