A. closed cycle
B. open cycle
C. both of the above
D. closed/open depending on other con-siderations
E. unpredictable
Correct Answer: closed cycle ✔
Last Updated: January 24, 2019
Related MCQs
- A closed gas turbine in which fuel is burnt directly in the air is not possible because of__________?
- In the axial flow gas turbine, the work ratio is the ratio of__________?
- Water is injected in gas turbine cycle to__________?
- The closed cycle in gas turbines__________?
- The degree of reaction of an axial flow turbine is the ratio of isentropic temperature drop in a blade row to the__________?
- A gas turbine used in air craft should have__________?
- Producer gas is produced by__________?
- For an irreversible gas turbine cycle, the efficiency and work ratio both depend on__________?
- It is not possible to use closed gas turbine cycle in aeronautical engines because__________ ?
- As the turbine inlet temperature increases, the thermal efficiency of gas turbine for the optimum pressure ratio__________?
- The jnaximum combustion pressure in gas turbine as compared to I.C. engine is__________?
- The material commonly used for air craft gas turbine is__________?
- The ideal efficiency of simple gas turbine cycle depends on__________?
- There is a certain pressure ratio (optimum) for a gas turbine at which its thermal efficiency is maximum. With increase in turbine temperature, the value of pressure ratio for the peak efficiency would__________?
- The combustion efficiency of a gas turbine using perfect combustion chamber is of the order of__________?
- Water gas is produced by __________ ?
- The thermal efficiency of a simple gas turbine for a given turbine inlet temperature with increase in pressure ratio__________?
- The following is true for an open cycle gas turbine having exhaust heat exchanger. Atmospheric air before entering the compressor is__________?
- Efficiency of gas turbine is increased by__________ ?
- The hottest point in a gas turbine is__________?
- Temperature of gases at end of compression as compared to exhaust gases in a gas turbine is__________?
- The pressure ratio in gas turbines is of the order of__________?
- The ratio of specific weighf/h.p. of gas turbin and I.C engines may be typically of the order of__________?
- The thermal efficiency of a gas turbine as compared to a diesel plant is__________?
- Gas turbine blades are given a rake__________?
- The air-fuel ratio in gas turbines is of the order of __________?
- Mechanical efficiency of gas turbines as compared to I.C engines is__________?
- The fuel consumption in gas turbines is accounted for by__________?
- The pressure ratio for an open cycle gas turbine compared to closed cycle gas turbine of same h.p. is__________?
- The work ratio of a gas turbine plant is defined as the ratio of__________?
- Rotary compressors are suitable for __________?
- Gas turbine works on__________?
- Gas turbine works on__________?
- The pressure ratio of an ideal vaned compressor with increase in mass flow rate__________?
- Actual compression curve is__________?
- The ratio of the increase in pressure in rotor blades to total increase in pressure in the stage is called__________?
- Surging phenomenon in centrifugal com-pressor depends on __________?
- Gas turbines for power generaion are normally used__________?
- Open cycle gas turbine works on__________?
- The work ratio of simple gas turbine cycle depends on__________?
- The vloumetric efficiency of compressor with increase in compression ratio will __________?
- Axial flow compressor resembles__________ ?
- Atmospheric pressure is 1.03 kg/cm and vapour pressure is 0.03 kg/cm . The air pressure will be__________ ?
- Axial flow compressor has the following advantage over centrifugal compressor__________?
- Maximum delivery pressure is a rotary air compressor is of the order of__________?
- The thermodynamic efficiency of rotary compressor is based on__________?
- Surging is the phenomenon of__________?
- The maximum compression ratio in an actual single stage axial flow comperssor is of the order of__________?
- The ratio of isentropic work to euler’s work is known as __________?
- The ratio of outlet whirl velocity to blade velocity in case of centrifugal compressor is called__________?
- More than one stage will be preferred for reciprocating compressor if the delivery pressure is more than__________?