A. right hand with same pitch
B. left hand with same pitch
C. could be left or right hand
D. right hand with fine pitch
E. left hand with fine pitch
Correct Answer: left hand with same pitch ✔
Last Updated: January 27, 2019
Related MCQs
- Applications in which stresses are encountered in one direction only uses following type of threads__________?
- A bench vice has following type of threads__________?
- Split nut is a locking device in which__________?
- The function of cutting oil when threading a pipe is to__________?
- For tight leakage joints, following type of thread is best suited __________?
- A tube has the following advantage over pipe__________?
- A backing ring is used inside the pipe joint when making a__________?
- Castle nut is a locking device in which__________?
- Gear box is used__________?
- The piston rod of a steam engine is usually connected to the cross head by means of__________?
- Spring index is__________?
- Form coefficient of spring is __________?
- When two springs are in series (having stiffness K), the equivalent stiffness will be__________?
- If a spring is cut down into two springs, the stiffness of cut springs will be __________?
- Aircraft body is usually fabricated by__________?
- In hydrodynamic bearings__________?
- If p = bearing pressure on projected bearing area, z = absolute viscosity of lubricant, and N = speed of journal, then the bearing characteristic number is given by__________?
- In hydrostatic bearings __________?
- The rated life of a bearing varies__________?
- In V-belt drive, belt touches__________?
- In cross or regular lay ropes__________?
- If shearing stress in nut is half the tensile stress in a bolt, then nut length should be equal to__________?
- Basic hole is one__________?
- For standard coarse threads of nut, the threads will be as strong in failure by shear as the bolt in tension, if the height of nut (h) is approximately__________?
- The resultant axial load on a bolt depends on__________?
- When a bolt is subjected to shock loading, the resilience of the bolt should be considered in order to prevent breakage at__________?
- The connecting rod bolts are tightened up with initial tension greater than the external load so that__________?
- The shock absorbing capacity of a bolt can be increased by__________?
- If an application calls for stresses on screw threads in one direction only, then the following type of thread would be best suited __________?
- The connecting rod bolts are tightened up so that tightening stress __________?
- Allen bolts are__________?
- I.S. specifies following total number of grades of tolerances__________?
- In composite or reverse laid ropes__________?
- Basic shaft is one__________?
- Whether any core is required in wire ropes__________?
- In standard taper roller bearings, the angle of taper of outer raceway is__________?
- Three different weights fall from a certain height under vacuum. They will take__________?
- In oilness bearings__________?
- Oil in journal bearing should be applied at the point where load is__________?
- The usual clearance provided in hydrodynamic bearing per mm of diameter of shaft is__________?
- Antifriction bearings are__________?
- If two springs are in parallel then their overall stiffness will be__________?
- Belt slip may occur due to__________?
- When a close coiled helical spring is compressed, its wire is subjected to__________?
- Spring stiffness is__________?
- The shearing stresses in the inner face as compared to outer face of the wire in a heavy close coiled spring is__________?
- Which of the following pipe joints would be suitable for pipes carrying steam__________?
- The edges of the plates for cylindrical vessels are usually bevelled to an angle of 80° for__________?
- When a nut is tightened by plaping a washer below it, the bolt will be subjected to following type of loads__________?
- The shear plane in case of bolts should__________?
- The strap end of a connecting rod of steam engine is joined by__________?