A. bolted joint
B. kunckle joint
C. cotter joint
D. universal joint
E. universal coupling
Correct Answer: cotter joint ✔
Last Updated: January 27, 2019
Related MCQs
- Spring index is__________?
- Form coefficient of spring is __________?
- When two springs are in series (having stiffness K), the equivalent stiffness will be__________?
- If a spring is cut down into two springs, the stiffness of cut springs will be __________?
- Aircraft body is usually fabricated by__________?
- In hydrodynamic bearings__________?
- If p = bearing pressure on projected bearing area, z = absolute viscosity of lubricant, and N = speed of journal, then the bearing characteristic number is given by__________?
- In hydrostatic bearings __________?
- The rated life of a bearing varies__________?
- In V-belt drive, belt touches__________?
- In cross or regular lay ropes__________?
- If shearing stress in nut is half the tensile stress in a bolt, then nut length should be equal to__________?
- Basic hole is one__________?
- For standard coarse threads of nut, the threads will be as strong in failure by shear as the bolt in tension, if the height of nut (h) is approximately__________?
- The resultant axial load on a bolt depends on__________?
- When a bolt is subjected to shock loading, the resilience of the bolt should be considered in order to prevent breakage at__________?
- The connecting rod bolts are tightened up with initial tension greater than the external load so that__________?
- The shock absorbing capacity of a bolt can be increased by__________?
- If an application calls for stresses on screw threads in one direction only, then the following type of thread would be best suited __________?
- The connecting rod bolts are tightened up so that tightening stress __________?
- Allen bolts are__________?
- I.S. specifies following total number of grades of tolerances__________?
- In composite or reverse laid ropes__________?
- Basic shaft is one__________?
- Whether any core is required in wire ropes__________?
- In standard taper roller bearings, the angle of taper of outer raceway is__________?
- Three different weights fall from a certain height under vacuum. They will take__________?
- In oilness bearings__________?
- Oil in journal bearing should be applied at the point where load is__________?
- The usual clearance provided in hydrodynamic bearing per mm of diameter of shaft is__________?
- Antifriction bearings are__________?
- If two springs are in parallel then their overall stiffness will be__________?
- Belt slip may occur due to__________?
- When a close coiled helical spring is compressed, its wire is subjected to__________?
- Spring stiffness is__________?
- The shearing stresses in the inner face as compared to outer face of the wire in a heavy close coiled spring is__________?
- Which of the following pipe joints would be suitable for pipes carrying steam__________?
- The edges of the plates for cylindrical vessels are usually bevelled to an angle of 80° for__________?
- When a nut is tightened by plaping a washer below it, the bolt will be subjected to following type of loads__________?
- The shear plane in case of bolts should__________?
- The strap end of a connecting rod of steam engine is joined by__________?
- In order to permit the thermal expansion/contraction of tubing, it should be__________?
- Silver-based solder is used for__________?
- Taper on the cotter and slot is provided__________?
- The valve rod in a steam engine is connected to an eccentric rod by__________?
- The draw of cotter need not exceed__________?
- Taper usually provided on cotter is__________?
- If d is the normal diameter of a bolt in mm, then the initial tension in kg in a bolt used for making a fluid tight joint as for steam engine cover joint is calculated by the relation__________?
- Eye bolts are used for__________?
- Fibrous fracture occurs in__________?
- A key made from a cylindrical disc having segmental cross-section, is known as__________?