A. same time to reach earth
B. times proportional to weight to reach earth
C. times inversely proportional to weight to reach earth
D. unpredictable
E. none of the above
Correct Answer: same time to reach earth ✔
Last Updated: January 27, 2019
Related MCQs
- In oilness bearings__________?
- Oil in journal bearing should be applied at the point where load is__________?
- The usual clearance provided in hydrodynamic bearing per mm of diameter of shaft is__________?
- Antifriction bearings are__________?
- If two springs are in parallel then their overall stiffness will be__________?
- Belt slip may occur due to__________?
- When a close coiled helical spring is compressed, its wire is subjected to__________?
- Spring stiffness is__________?
- The shearing stresses in the inner face as compared to outer face of the wire in a heavy close coiled spring is__________?
- Which of the following pipe joints would be suitable for pipes carrying steam__________?
- The edges of the plates for cylindrical vessels are usually bevelled to an angle of 80° for__________?
- When a nut is tightened by plaping a washer below it, the bolt will be subjected to following type of loads__________?
- The shear plane in case of bolts should__________?
- The strap end of a connecting rod of steam engine is joined by__________?
- In order to permit the thermal expansion/contraction of tubing, it should be__________?
- Silver-based solder is used for__________?
- Taper on the cotter and slot is provided__________?
- The valve rod in a steam engine is connected to an eccentric rod by__________?
- The draw of cotter need not exceed__________?
- Taper usually provided on cotter is__________?
- If d is the normal diameter of a bolt in mm, then the initial tension in kg in a bolt used for making a fluid tight joint as for steam engine cover joint is calculated by the relation__________?
- Eye bolts are used for__________?
- Fibrous fracture occurs in__________?
- A key made from a cylindrical disc having segmental cross-section, is known as__________?
- In order to obtain bolt of uniform strength__________?
- The pitch of threads on a Jock nut in comparison to pitch of nut is__________?
- Transverse fillet welded joints are designed for__________?
- In order to avoid tearing of the plate at edge, the distance from the center line of the rivet hole to the nearest edge of the plate in terms of dia of rivet d should be equal to__________?
- The edges of a boiler plate are bevelled to an angle of__________?
- Machine screws are__________?
- A self locking screw has__________>
- Which is correct statement ?
- The endurance limit in shear of carbon steel can be obtained by multiplying the endurance limit in flexure by a factor of__________?
- A bolt__________?
- If d is the diameter of bolt hole then for a flanged pipe joint to be leak proof, the circumferential pitch of the bolts should be__________?
- The following type of nut is used with alien bolt__________?
- Shear stress theory is applicable for__________?
- For applications involving high stresses in one direction only the following type of thread would be best suited__________?
- The function of a washer is to__________?
- Ball bearing type screws are found in following application__________?
- An alien bolt is__________?
- Set screws are__________?
- The deflection of a cantilever beam under load W is 8. If its width is halved, then the deflection under load W will be__________?
- Cap screws are__________?
- The included angle in unified of American National threads is__________?
- A tap bolt__________?
- A stud__________?
- Maximum principal stress theory is applicable for__________?
- The crest diameter of a screw thread is same as __________?
- At low temperatures (say 75°C) the notched-bar impact value of steel__________?
- For steel, the ultimate strength in shear as compared to ultimate strength in tension is __________?