A. 10% of wall area
B. 20% of wall area
C. 30% of wall area
D. 50% of wall area
Correct Answer: 20% of wall area ✔
Last Updated: January 20, 2019
Related MCQs
- The risk coefficient k, depends on__________?
- The internal pressure coefficient on walls for buildings with large permeability is taken as__________?
- The relation between intensity of wind pressure p and velocity of wind V is taken as__________?
- Generally the purlins are placed at the panel points so as to avoid__________?
- Normally, the angle of roof truss with asbestos sheets should not be less than__________?
- The range of economical spacing of trusses varies from__________?
- Rivets connecting flange angles to cover plates in a plate girder are subjected to__________?
- Gantry girders are designed to resist__________?
- Bearing stiffener in a plate girder is used to__________?
- As per IS : 800, for compression flange, the outstand of flange plates should not exceed__________?
- Minimum thickness of web in a plate girder, when the plate is accessible and also exposed to weather, is__________?
- Shear buckling of web in a plate girder is prevented by using__________?
- The slenderness ratio of lacing bars should not exceed__________?
- The effective length of a battened column is increased by__________?
- Angle of inclination of the lacing bar with the longitudinal axis of the column should preferably be between__________?
- The use of tie plates in laced columns is__________?
- The best arrangement to provide unified behaviour in built up steel columns is by__________?
- A circular column section is generally not used in actual practice because__________?
- For a standard 45° fillet, the ratio of size of fillet to throat thickness is__________?
- The actual thickness of butt weld as compared to the thickness of plate is usually__________?
- According to IS Specifications, the effective length of a column effectively held in position at both ends and restrained in direction at one end is taken as__________?
- The maximum slenderness ratio of a compression member carrying both dead and superimposed load is__________?
- According to IS:800, in the Merchant Rankine formula the value of imperfection index (n) is__________?
- The maximum slenderness ratio of a steel column, the design of which is governed by wind or seismic forces is__________?
- According to IS Specifications, the maximum pitch of rivets in compression is__________?
- The effective length of a battened strut effectively held in position at both ends but not restrained in direction is taken as__________?
- The slenderness ratio of a column supported throughout its length by a masonry wall is__________?
- A butt weld is specified by__________?
- The effective length of a fillet weld should not be less than__________?
- When the bolts are subjected to reversal of stresses, the most suitable type of bolt is__________?
- Bolts are most suitable to carry__________?
- Efficiency of a riveted joint, having the minimum pitch as per IS : 800, is__________?
- As compared to field rivets, the shop rivets are__________?
- By providing sufficient edge distance, which of the following failures of riveted joint can be avoided ?
- In a gusseted base, when the end of the column is machined for complete bearing on the base plate, then the axial load is assumed to be transferred to base plate__________?
- Which of the following types of riveted joint is free from bending stresses ?
- The heaviest I-section for same depth is__________?
- If the thickness of plate to be connected by a rivet is 16 mm, then suitable size of rivet as per Unwin’s formula will be__________?
- The difference between gross diameter and nominal diameter for the rivets up to 25 mm diameter is__________?
- When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which__________?
- Bending compressive and tensile stresses respectively are calculated based on__________?
- When the axis of load lies in the plane of rivet group, then the rivets are subjected to__________?
- If the thickness of thinnest outside plate is 10 mm, then the maximum pitch of rivets in tension will be taken as__________?