A. equilibrium and mechanism conditions
B. equilibrium and plastic moment conditions
C. mechanism and plastic moment conditions
D. equilibrium condition only
Correct Answer: equilibrium and plastic moment conditions ✔
Last Updated: January 20, 2019
Related MCQs
- Load factor is__________?
- Other conditions being same, the load factor in indeterminate structures is__________?
- In the virtual work method, the virtual quantity is__________?
- The shape factor of an isosceles triangle for bending about the axis parallel to the base is__________?
- The minimum thickness of a steel plate, which is directly exposed to weather and is not accessible for cleaning and repainting, should be__________?
- Lug angles__________?
- The connection of intermediate vertical stiffeners to the web, not subjected to external loads, shall be designed for a minimum shear force (kN/m) of__________?
- For rivets in tension with counter-sunk heads, the tensile value shall be__________?
- In moment resistant connections, the moment resistance of riveted connection depends upon__________?
- Pitch of tacking rivets, when double angles connected back to back and acting as tension members should not be more than__________?
- The allowable shear stress in the web of mild steel beams decreases with__________?
- Hudson’s formula gives the dead weight of a truss bridge as a function of__________?
- A steel beam supporting loads from the floor slab as well as from wall is termed as__________?
- For a compression member with double angle section, which of the following section will give larger value of minimum radius of gyration?
- The moment of inertia of the pair of vertical stiffeners about the center line of the web should not be less than__________?
- In case of plastic design, the calculated maximum shear capacity of a beam as per IS:800 shall be__________?
- As per IS:800, in the plastic design, which of the following pairs are correctly matched? Working Loads Load factor__________?
- Which of the following conditions is to be satisfied both in elastic and plastic analysis ?
- The ratio of plastic section modulus to elastic section modulus__________?
- The mechanism method of plastic analysis satisfies__________?
- Shape factor is a property which depends__________?
- The mechanism method and the statical method give__________?
- In case of timber structures, the simple bending formula M = fz may be applied for__________?
- The least dimension in case of a circular column of diameter D is taken as__________?
- The bracing provided in the plane of end posts is called__________?
- The sway bracing is designed to transfer__________?
- The effect of racking forces is considered in the design of__________?
- If the floor is supported at or near the bottom but top chords of a bridge are not braced, then the bridge is called__________?
- Maximum pitch of rivets, used in steel stacks, is limited to__________?
- The bracing between two columns of a steel tank will be designed to resist__________?
- Which of the following sections should preferably be used at places where torsion occurs ?
- The allowable tensile stress in structural mild steel plates for steel tank is assumed as__________?
- The number of seismic zones in which the country has been divided are__________?
- Area of openings for buildings of large permeability is more than__________?
- The risk coefficient k, depends on__________?
- The internal pressure coefficient on walls for buildings with large permeability is taken as__________?
- The relation between intensity of wind pressure p and velocity of wind V is taken as__________?
- Generally the purlins are placed at the panel points so as to avoid__________?
- Normally, the angle of roof truss with asbestos sheets should not be less than__________?
- The range of economical spacing of trusses varies from__________?
- Rivets connecting flange angles to cover plates in a plate girder are subjected to__________?
- Gantry girders are designed to resist__________?
- Bearing stiffener in a plate girder is used to__________?
- As per IS : 800, for compression flange, the outstand of flange plates should not exceed__________?
- Minimum thickness of web in a plate girder, when the plate is accessible and also exposed to weather, is__________?
- Shear buckling of web in a plate girder is prevented by using__________?
- The slenderness ratio of lacing bars should not exceed__________?
- The effective length of a battened column is increased by__________?
- Angle of inclination of the lacing bar with the longitudinal axis of the column should preferably be between__________?
- The use of tie plates in laced columns is__________?
- The best arrangement to provide unified behaviour in built up steel columns is by__________?